background image

9

Installation

Selection of installation location

Put the portable air conditioner in a fl at location where the air 
outlets cannot be covered up, place the unit no less than 20 in. 
(50 cm)  away from a wall or other obstacle.

22 inch

18 inch

Mounting the intake and exhaust hoses

1)  Fit one end of the exhaust hose to the exhaust terminal of 

the unit then rotate it 2 - 3 revolutions to tighten the hose into 
the terminal.

2)  Put the other end (discharge) to the nearest window.

3)  Install the intake hose in the same manner 

Note: The length of the air intake and exhaust hoses are be-
tween 24" - 72".  Try to keep the hose as straight and horizontal 
as possible.

Air 
intake 
terminal

Air intake hose

Air exhaust terminal

Instructions to install hose

If the hose becomes disconnected from the hose fi tting it must be 
reinserted. Fit the hose to the hose fi tting then rotate it 2-3 revolu-
tions to tighten the hose into the fi tting.  See fi gure below:

Correct mounting shown below

(If mounting in the wall, the height of the hole should be 16" - 51")

Troubleshooting

Self diagnosis function

The following error codes are pre-programmed into each unit to 
help identify possible unit conditions.

Failure code

Diagnosis of Malfunction

E2

Room Temperature sensor failure

E3

Coils sensor failure

E4

Unit malfunction

E5

Water level exceeded capacity

Содержание ZoneAir P-09













Отзывы: