Friedrich XStar EQ08M11-A Скачать руководство пользователя страница 42

Страница: 42 / 47

Following is an example using the heat load form:

A space to be conditioned is part of a house geographically

located in an area where the lowest outdoor ambient winter

temperature is 40°F. The calculated heat loss is 184 BTU/

Hr./°F.

Subtract 40°F (lowest outdoor ambient temperature for the

geographical location) from 70°F (inside design temperature

of the unit) for a difference of 30°F. Multiply 184 by 30 for a

5500 BTU/Hr. total heat loss for the calculated space.

On the graph, plot the base point (70°) and a point on the

40°F line where it intersects with the 5500 BTU/Hr. line on

the left scale. Draw a straight line from the base point 70

through the point plotted at 40°F. This is the total heat loss

line.

Knowing that we have a 5500 BTU/Hr. heat loss, and

we expect that our heat pump will maintain a 70°F inside

temperature at 40°F outdoor ambient, we plot the selected

unit capacity BTU/Hr. of the unit between 35° and 60° on the

graph and draw a straight line between these points. Where

the total heat loss line and the unit capacity line intersect,

read down to the outdoor ambient temperature scale and

ﬁ nd that this unit will deliver the required BTU/Hr. capacity

to approximately 30°F.

The heat load form on the following page may be used by

servicing personnel to determine the heat loss of a conditioned

space and the ambient winter design temperatures in which

the unit will heat the calculated space.

The upper half of the form is for computing the heat loss of

the space to be conditioned. It is necessary only to insert

the proper measurements on the lines provided and multiply

by the given factors, then add this result for the total heat

loss in BTU/Hr./°F.

The BTU/Hr. per °F temperature difference is the 70°F

inside winter designed temperature minus the lowest outdoor

ambient winter temperature of the area where the unit is

installed. This temperature difference is used as the multiplier

when calculating the heat loss.

The graph shows the following:

Left Hand Scale

Unit capacity BTU/Hr. or heat loss

BTU/Hr.

Bottom Scale

Outdoor ambient temperature, base

point.

Heat Pump Model

BTU/Hr. capacity heat pump will

deliver at outdoor temperatures.

Balance Point

Maximum BTU/Hr. heat pump

will deliver at indicated ambient

temperature.

HEAT LOAD FORM

Содержание XStar EQ08M11-A
















































Результаты поиска

Содержание XStar EQ08M11-A

Отзывы:

Бренды по названию

Популярные бренды

Friedrich XStar EQ08M11-A, Руководство по обслуживанию

Результаты поиска

Содержание XStar EQ08M11-A

Отзывы:

Бренды по названию

Популярные бренды