background image

22

Wire Size

Use 

ONLY

 wiring size recommended for

single outlet branch circuit.

Fuse/Circuit

Use 

ONLY 

type and size fuse or HACR

Breaker

circuit breaker indicated on unit's rating
plate.  Proper

current protection to the unit

is the responsibility of the owner.

Grounding

Unit 

MUST 

be grounded from branch circuit

through service cord to unit, or through
separate ground wire provided on
permanently connected units.  Be sure that
branch circuit or general purpose outlet is
grounded.

Receptacle

The field supplied outlet must match plug on
service cord and be within reach of service
cord.
Do 

NOT 

alter the service cord or plug.  Do

NOT

 use an extension cord.  Refer to the

table above for proper receptacle and fuse
type.

Circuit Rating

P

lug Face

Appearance

Model

Breaker or T-D Fuse

(NEMA#)

(Facing Blades)

ALL KQ, SQ and XQ MODELS,

KS10J10, KS12J10A, KM14J10, RS10J10, RS12J10A,
RM14J10, SS08J10R, SS09J10B, SS10J10R,
SS12J10AR, SM14J10R, SC06H10D,

125V - 15A

5 - 15P

YQ06J10A, YS09J10,WS07A10D, WS09A10D, WS12A10D
KS12J30A, KM18J30B, RS16J30,
RM19J30, SS12J30B, SS16J30,

250V - 15A

6 - 15P

SM19J30R, WS09A30D, WS12A30D, WS13A30D

KM21J30, KL25J30A, SM21J30B,
SL24J30A, SL28J30A*, ES12J33, EK12J33A,
ES16J33, YS13J33, WE09A33D, WE12A33D,

250V - 20A

6 - 20P

WE13A33D, WY09A33D, WY12A33E

SL33J30, EM19J34, EK18J34B, EL24J35A,
EL33J35, YM18J34A, YL24J35A

250V - 30A

6 - 30P

* Optional 30 Amp Kit (618-869-00) is recommended in 208 Volt power supply areas that fall below 208 Volts.

For more information, call the Friedrich Service Department.

Due to a program of continuing improvement, specifications are subject to change without notice.

INSTALLATION NOTES:

Supply Cord - All with right angle plug 6' on 115V; 5' on 230/208V.
Room air conditioners include accessories for window or thru-wall
installation.  TwinTemp models include accessories for thru-wall
installation. Window mounting requires use of optional
accessory kit as listed below:

Electrical Rating T

Electrical Rating T

Electrical Rating T

Electrical Rating T

Electrical Rating Tables

ables

ables

ables

ables

Electric shock hazard.

Electric shock hazard.

Electric shock hazard.

Electric shock hazard.

Electric shock hazard.

Turn off electric power before service or installation.

All electrical connections and wiring MUST be installed by a qualified
electrician and conform to the National Electrical Code and all local
codes which have jurisdiction.

Failure to do so can result in property damage, personal injury and/or
death.

FRIEDRICH AIR CONDITIONING CO

FRIEDRICH AIR CONDITIONING CO

FRIEDRICH AIR CONDITIONING CO

FRIEDRICH AIR CONDITIONING CO

FRIEDRICH AIR CONDITIONING CO.....

Post Office Box 1540 

 San Antonio, Texas 78295-1540

4200 N. Pan Am Expressway 

 San Antonio, Texas 78218-5212

(210) 357-4400 

 FAX (210) 357-4480

Visit us on the Internet at www.friedrich.com

The consumer - through the AHAM Room Air Conditioner
Certification Program - can be certain that the AHAM
Certification Seal accurately states the unit's cooling and
heating capacity rating, the amperes and the energy
efficiency ratio.

Содержание SM21J30A4







































































Отзывы: