manualshive.com logo in svg

Fresenius Medical Care T688 Series, Руководство по обслуживанию

Поделиться
Скачать
Fresenius Medical Care T688 Series Скачать руководство пользователя страница 6

 
 

 

Troubleshooting 

Fresenius Medical Care 

T688 Series   

5 

V1 Aug 2020 

 

 

In the event the chair fails to operate correctly, please take the following steps 

prior to contacting 

Fresenius Medical Care or its authorised agent. 

1. Check that the mains power outlet is active. 

2. Check that the power cord is not damaged or worn. Check that the chair is connected into the 

mains power outlet and switched on correctly, as indicated by the green indicator light on the 

nurse’s hand control. 

3. Ensure that the battery has been on charge for 24 hours minimum. This should occur at least 

every 5 days. 

4. Ensure there are no damage or cuts in the cables to the hand controls or actuators.  

5. Determine which functions are not operating as follows: 

Problem / Failure 

Action / Solution 

The leg rest motor (vertically mounted under the 

seat)  

Depress the hand control button for the leg rest 

and the leg rest should raise or lower.  

The backrest motor (mounted behind the 

backrest) 

Depress the hand control button for the backrest 

and the back should raise or lower. 

The lift column (mounted on top of the base)  

 

Depress the hand control button for the chair 

height control and the chair should raise or 

lower. 

 

Take note of the serial number of the chair. This information can be found on the Type Label  

(

Figure 1 or 2. Type Label 

– Serial number location section

) attached to the chair.  

If unsure about any aspect of the above steps, please contact Fresenius Medical Care Seating at the 

contact details provided at the end of this service manual (see 

Contact Information

 section). 

 

➢

 

Hand Control 

– Programming  

Note.This can only be done using the 

nurse’s hand control. A maximum of three positions may be 

programmed into the memory.  

1.  Position the chair to the desired position using the up & down arrows for the backrest, whole 

chair and leg rest.  

2.  When the chair is in the desired position, hold down the S (store) button for five seconds until 

the beep sounds.  

3.  Once the beep is sounding, select one of the numbers, 1, 2, or 3 and press it within two 

seconds to store the pre-programmed position. When completed the system will beep two 
times to confirm.  

 

 

 

Содержание T688 Series























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды