freightliner C SB FS65 Скачать руководство пользователя | Manualshive

Страница: 43 / 91

background image

Lubricant Capacities, Allison AT/MT/MD Series

Transmissions

Model

Refill Capacity

*

:

Quarts (liters)

AT–542

16.0 (15.1)

AT–545

21.0 (19.9)

MT–643

19.0 (18.0)

MD–3060P

17.5 (16.5)

MD–3060PR

*

Quantities listed are approximate. Add the recommended amount of fluid

as listed under refill capacity, then perform a "hot check" and add fluid as
needed. Do not overfill.

Table 4, Lubricant Capacities, Allison AT/MT/MD

Series Transmissions

MD Series

1.

See

Fig. 5

. Park the vehicle on a level surface

and set the parking brake.

2.

Run the engine until the transmission fluid
reaches an operating temperature of 160 to
200°F (71 to 93°C). Shift the transmission to
Neutral (N) and shut down the engine.

CAUTION

To prevent dirt from entering the transmission,
use only clean containers and fillers for the trans-
mission fluid. Do not use fillers or containers that
have been used for water or antifreeze. Dirt, water,
or antifreeze could damage the transmission.

3.

Clean the area around the drain plug. While the
transmission fluid is warm, remove the drain
plug, and drain the fluid.

IMPORTANT: Examine the used transmission
fluid for dirt, coolant or water, and metal par-
ticles. If any of these contaminants are present,
a problem within the transmission system may
exist.

4.

Remove the bolts from each filter cover at the
bottom of the transmission control module. Re-
move the filter covers, O-rings, seals, and the
two cartridge-type filters.

5.

Coat the O-rings lightly with clean transmission
fluid. Place the O-rings, seals, and filters on the
filter covers. Push each cover assembly into the
bottom of the transmission to seat the seals. In-

stall and tighten the bolts 38 to 45 lbf·ft (52 to 61
N·m). Install and tighten the drain plug 18 to 24
lbf·ft (24 to 33 N·m).

6.

Clean the area around the fill tube and remove
the dipstick. Using a clean funnel in the fill tube,
add transmission fluid. See

Table 3

for approved

transmission lubricants, and see

Table 4

for MD

series lubricant capacities.

7.

Check and adjust the fluid level using the proce-
dures under "Allison Transmission Fluid Level
Checking."

f260130a

1

2

3

4

5

6

7

06/04/99

1.

Drain Plug O-Ring

2.

Drain Plug

3.

Filter

4.

Filter O-Ring

5.

Seal

6.

Filter Cover

7.

M10 Bolt

Fig. 5, Allison MD Series Transmission

Transmission

26

School Bus Chassis Maintenance Manual, March 2003

26/5

«
...
41
42
43
44
45
...
»

Содержание C SB FS65




























































































Отзывы:

Нет отзывов

Похожие инструкции для C SB FS65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды