manualshive.com logo in svg

Freight Wing Aeroflex, Руководство пользователя

Поделиться
Скачать
Freight Wing Aeroflex Скачать руководство пользователя страница 14

 

14 

4c. Place a rubber bonded washer on the bolt next to the plain nut with the metal side facing the 

nut. Then place a clamp tab on the bolt with the angle facing the thread. Then place the bolt 
sleeve on the bolt. Then place another clamp tab on the bolt with the angle facing the other 
clap tab such that they are opposing. Then place another rubber bonded washer on the bolt 
with  the  rubber  side  facing  the  clamp  tab.  Finish  by  hand  tightening  a  nylon  insert  lock  nut. 
The completed assembly is illustrated below: 

    

 

4d. Repeat the process for all 16 rods in each unit.   

 

The pre assembly is now complete and the fairing is ready for installation on the trailer 
(see trailer installation manual). 

If you have any other problems, questions or comments regarding the installation 
procedure, please call our toll free installation help line: 

TOLL FREE INSTALLATION HELP LINE: 866-464-9464 

 

Содержание Aeroflex















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды