10
ELECTRICAL CONNECTION
This oven must be installed and connected to its place correctly according to
manufacturer instructions and by an authorized service.
Appliance must be installed in an oven enclosure providing high ventilation.
Electrical connections of the appliance must be made only via sockets having earth
system furnished in compliance with rules. Contact an authorized electrician if there
is no socket complying with the earthed system at where appliance will be placed.
Manufacturing company is by no means responsible for damage resulting from
connection of non-earthed sockets to appliance.
Plug of your oven must be earthed; ensure that socket for the plug is earthed. Plug
must be located in a place that can be accessed after installation.
Your oven has been manufactured as 220-240 V 50/60 Hz. AC power supply compliant
and requires a 16 Amp fuse. If your power network is diff erent that these indicated
values, refer to an electrician or your authorized service.
When you need to replace the electrical fuse, please ensure that electrical connection
is made as follows:
•
Phase (to live terminal) brown cable
•
Blue cable to neutral terminal
•
Yellow-green cable to earth terminal
Oven disconnecting switches must be in an accessible place for fi nal user while oven
is in its place.
Power supply cable (plug in cable) mustn’t touch hot parts of the appliance.
If supply cord (plug in cable) is damaged, this cord must be replaced by the importer
or its service agent or an equally competent personnel to prevent a hazardous
situation.
GAS CONNECTION
WARNING: Before starting any work related with gas installation, turn off
gas supply. Risk of explosion.
WARNING: Gas hose and electric connection of the appliance should not
pass next to hot areas such as back of the appliance. Gas hose should
be connected by making wide angle turns against breaking possibility.
Movement of appliance whose gas connection is made may cause gas
leakage.
WARNING: While making gas leakage control; never use lighter, match,
glowing cigarette or similar infl ammable matter.
Connect your appliance to gas oven from the shortest way and in a manner to
prevent any leakage. For safety, the hose used should be maximum 125 cm and
minimum 40 cm.
Apply soap bubble on connection point. If any leak/leakage exists, foaming will
occur on soaped region.
FOR LPG CONNECTION
For LPG (cylinder) connection, affi
x metal clamp on
the hose coming from LPG cylinder. Affi
x an edge
of the hose on hose inlet connector behind the
appliance by pushing to end through heating the
hose in boiled water. Afterward, bring the clamp
towards end section of the hose and tighten it with
screwdriver. The gasket and hose inlet connector
required for connection is as the picture shown
below.
WARNING: The regulator to be affi
xed on LPG cylinder should have 300
mmSS feature.
FOR NATURAL GAS CONNECTION
WARNING: Natural gas connection should
be done by authorized service.
For natural gas connection, place gasket
in the nut at the edge of natural gas connection
hose. To install the hose on main gas pipe,
turn the nut. Complete the connection by
making gas leakage control.
ELECTRICAL CONNECTION
GAS CONNECTION
VENTILATION OF ROOM
The air needed for burning is received from room air and the gases emitted are
given directly in room. For safe operation of your product, good room ventilation is
a precondition. If no window or room to be utilized for room ventilation is available,
additional ventilation should be installed. However, room has a door opening
outside, it is no needed to vent holes.
REMOVAL OF THE LOWER AND UPPER BURNER AND
INSTALLATION OF THE INJECTOR TO THE GAS OVEN
•
REMOVAL OF THE UPPER BURNER:
With the help of a screw driver, remove the screw as shown in fi gure 3. As shown in
fi gure 4, remove the burner from its place by pulling it to yourself. As shown in fi gure
5, remove the injector in the bearing with a socket wrench. In order to re-place the
burner, apply the removal process reversely.
Room size
Ventilating opening
Smaller than 5 m³
min. 100 cm²
Between 5 m³ - 10 m³
min. 50 cm²
Bigger than 10 m³
No need
In basement or cellar
min. 65 cm²
Main Gas Pipe
Gasket
Hose Inlet Connector
Metal Clamp
Lpg Connection Hose
Figure 1
Figure 3
Figure 4
Figure 5
Figure 2
Main Gas Pipe
Gasket
Nut
Natural Gas
Connection Hose
REDUCED GAS FLOW RATE SETTING FOR HOB TAPS
1.
Ignite the burner that is to be adjustment and turn the knob to the reduced
position.
2.
Remove the knob from the gas tap.
3.
Use an appropriately sized screwdriver to adjust the fl ow rate adjustment
screw. For LPG (butane-pro pane) turn the screw clockwise. For the naturel gas,
you should turn the screw counter- clockwise once.
“The normal length of a straight fl ame in the reduced position should be 6-7 mm.“
4.
If the fl ame is higher then the desired position, turn the screw clockwise. If it is
smaller turn anticolockwise.
5.
For the last control, bring the burner both to higt-fl ame and reduced positions
and check whether the fl ame is on or off .
Depending on the type of gas tap used in your appliance the adjustment screw
position may vary.
To adjust your oven acc. to the gas type, make the adjustment for reduced fl ame
carefully by turning with a small screwdriver as shown below on the screw in the
middle of the gas cocks as well as nozzle changes (fi gure 1 and 2)
•
REMOVAL OF THE LOWER BURNER:
The lower burner door has been fi xed with two screws. As shown in fi gure 6, remove
it with the help of a screw driver. Remove the door by pulling upwards as shown in
fi gure 7. Remove the burner from its place by pulling it to yourself as shown in fi gure
8. As shown in fi gure 9, remove the injector in the bearing with a socket wrench. In
order to replace the burner, apply the removal process reversely.
Figure 6
Figure 7
