BASIC FEATURES
The Monitor integrates a bright 24in display with a high performance system, USB ports, and integrated
options such as capacitive touch, hot-swappable batteries, and smart card reader for a comprehensive point-
of-healthcare solution.
Powering ON and OFF
If your Monitor comes with the battery packs, please open the battery slot caps and then put in the battery
packs one by one. If not, please use the AC-DC adapter with the Monitor for the power supply. To activate
the Monitor, push and quickly release the Power Button and the display will come on in a few seconds. To
put in Standby mode, push and quickly release the Power Button. To turn off for extended storage, power
off the device safely using any software function that “shuts down computer” provided in the software
operating system.
PRECAUTIONS
• Always exercise care when operating and handling
the Monitor.
• Never disassemble any portion of the enclosure, as
this will void any product warranty on the Monitor.
• Do not use any AC/DC adapter other than the
one provided with the device or a replacement
acquired from the manufacturer.
• In the unlikely event that smoke, abnormal noise or
strange odour is present, immediately power down
the Monitor and disconnect all power sources.
Please report the problem to your device provider
immediately.
Power/Battery LED Status
• Blue indicates the battery is 25% to 100% charged
• Blinking blue indicates the battery is charging
• Orange indicates that the battery is between 11% to25%
• Blinking Orange indicates that the battery is below 10%
Wireless Networking
Wireless LAN
The Monitor is often delivered with an embedded (user-inaccessible) 802.11ax WLAN adapter equipped with
a hidden custom antenna.
• Through the support of typical WLAN adapters, the Monitor should be able to detect all 802.11 access
points in the vicinity for you to select the access point of your choice for connection.
• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the Monitor and the access points have to
match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or
advanced alternatives) for secure access.
• When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your
networking equipment literature to properly configure associated settings such as Authentication mode, etc.
• Refer to the access point operating manuals for setting up the 802.11 access points.
Bluetooth
The Monitor features a built-in Bluetooth adapter that operates on the Microsoft Windows Bluetooth
protocol. The Bluetooth configuration application is invoked from the System Tray or from the Control
Panel. Follow the instructions and options provided within the application to configure and invoke Bluetooth
connectivity with the corresponding peripherals.
CLEANING THE MT700-24T MONITOR
You can clean the MT700-24T as often as required. All health care institutions will have a recommended
minimum frequency for routine cleaning of various items within their facility. This may be weekly, daily or after
each use depending on the risk involved.
The screen
• An antibacterial cleaning solution (70% alcohol) that is non-abrasive can be used to clean the touch screen.
• Cleaning with a micro-fiber cloth is recommended.
• Please spread the solution onto the cloth and then clean the touch screen.
• It is recommended to wipe the screen in a top to bottom motion and finish across the bottom to minimise
streaking and to prevent excess moisture running down off the bezel.
The anti-microbial enclosure
• Use a soft/non-abrasive cloth moistened with cleaning solution (70% alcohol) to clean the enclosure.
• To prevent scratching the anti-microbial coating, please wipe gently.
IMPORTANT NOTES
1.
The battery packs (optional) shipped with your
device may be low in power - please use the AC-
DC adapter with the Monitor when setting up the
device for the first time to fully charge the battery
packs. You may charge the battery packs with them
attached to the Monitor or with the optional battery
charger kit.
2.
When the battery packs are charging, the blue-
coloured Battery LED should blink slowly. If plugging
in the AC-DC adapter does not trigger this blinking
activity and the LED stays dark, the battery pack(s)
may have been drained substantially. Try unplugging/
plugging in the AC-DC adapter to the Monitor a few
times to activate the charging process.
3.
To conserve power, use (push and quick release)
the Power Button to put the device in “Standby”
mode while not in use. Pushing briefly on the same
button will wake up the system within seconds.
4.
Avoid using the Power Button (“hold 4+ seconds”
feature) to turn off the device—this form of
hardware shutdown is intended to be a means of
recovery from device lockups, and not as normal
operation.
5.
If connecting an external monitor to the Monitor
(via HDMI port), you must power the Monitor with
the provided AC-DC power adapter.
freewaymedtech.com
MT700-24T Basic operation guide
Battery status LEDs
