Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 617 | Manualshive

Страница: 617 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

16-40

Freescale Semiconductor

internal counter is disabled and its content is transferred to register A2. At the same time the FLAG bit is
set. Reading registers EMIOS_ALTA

n

or A2 returns the amount of detected pulses.

For continuous operation (MODE[6] cleared), the next match between comparator A and the selected time
base clears the internal counter and counting is enabled again. To guarantee the accuracy when reading
EMIOS_CCNTR

n

after the flag is set, the software must check if the time base value is out of the time

interval defined by registers A1 and B1. Alternatively register A2 always holds the latest available
measurement providing coherent data at any time after the first FLAG occurs. This register is addressed
by the alternate address EMIOS_ALTA

n

.

For single shot operation (MODE[6] set), the next match between comparator A and the selected time base
has no effect, until a new write to register A is performed. The EMIOS_CCNTR

n

content is also

transferred to register A2 when a match in the B comparator occurs.

NOTE

The FORCMA and FORCMB bits have no effect when the unified channel
is configured for PEC mode.

show how the unified channel can be used for continuous or single shot

pulse/edge counting mode.

Figure 16-27. Pulse/Edge Counting Continuous Mode Example

Selected

counter bus

0x000090 0x000090

B1 value

2

0x000090

0x000303

0x000303

0x000303

Amount of

EMIOS_CCNTR

n

FLAG

set event

MODE[6] = 0

A1 match

B1 match

B1 match

A1 value

1

Notes:

1

Writing EMIOS_CADR

n

writes to A1.

2

Writing EMIOS_CBDR

n

writes to B1.

Time

0x000000

events

detected

A1 match

A1 and B1

Write

0x000090

0x000303

0x000090

0x000303

A2 value

3

3

Reading EMIOS_ALTA

n

returns the value of A2.

A2 EMIOS_CCNTR

n

A2 EMIOS_CCNTR

n

«
...
615
616
617
618
619
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Jetline Страницы: 58

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: Vageo Страницы: 2

SR-ZG9001T-RGBW

Бренд: Sunricher Страницы: 3

Бренд: IDTECK Страницы: 51

Бренд: Sorel Страницы: 20

Бренд: Inca Страницы: 11

DMX-LED-DIMMER X9 HR

Бренд: DMX4ALL Страницы: 14

Бренд: AMX Страницы: 2

Бренд: Zonet Страницы: 2

Бренд: Intrinsyc Страницы: 38

Бренд: Omron Страницы: 157

Бренд: National Instruments Страницы: 31

Бренд: Duke Страницы: 4

DD-1920-DUAL-DVI

Бренд: Digital View Страницы: 30

Бренд: Norgren Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды