Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 291 | Manualshive

Страница: 291 / 1153

background image

System Integration Unit (SIU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

6-116

Freescale Semiconductor

The SIU contains an overrun request for each IRQ and one combined overrun request which is the logical
OR of the individual overrun requests. Only the combined overrun request is used in the device, and the
individual overrun requests are not connected.

Each IRQ pin has a programmable filter for rejecting glitches on the IRQ signals. The filter length for the
IRQ pins is specified in the external IRQ digital filter register (SIU_IDFR).

Figure 6-158. SIU DMA/Interrupt Request Diagram

6.4.4

GPIO Operation

All GPIO functions for the device are provided by the SIU. Each device pad that has a GPIO signal has a
pin configuration register (PCR) in the SIU where the GPIO function is selected. In addition, each device
GPIO signal has an input data register (SIU_GPDI

n

) and an output data register (SIU_GPDO

n

).

6.4.5

Internal Multiplexing

The internal multiplexing select registers (SIU_ETISR, SIU_EIISR, and SIU_DISR) select the input
source for the following components:

•

eQADC external trigger input signals

•

SIU external interrupt request signals

•

DSPI signals used for chaining serial and parallel DSPI modules

Interrupt

controller

DMA/

interrupt

select

•

•

•

•

•

0
1
2
3
4

15

IMUX

Interrupt

request

DMA

request

DMA

•

•

•

0
1

15

SIU_OSR

SIU_EISR

Overrun

request

EIRQ pins

or

internal

source

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Interrupt

request

SIU_DISR

SIU

«
...
289
290
291
292
293
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

TEMP2000 Series

Бренд: Samwontech Страницы: 91

Бренд: Vaillant Страницы: 11

Бренд: Dahua Страницы: 137

Бренд: POLA Страницы: 2

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: Maximum Controls Страницы: 58

Бренд: Shimaden Страницы: 16

Touch Screen Controller RX142

Бренд: 3M Страницы: 29

Бренд: Vectornav Страницы: 18

Бренд: Progres Страницы: 2

Бренд: salmson Страницы: 37

Бренд: Airone Страницы: 2

Бренд: H3C Страницы: 3

CapSense Plus CY3280-CPM1

Бренд: Cypress Страницы: 4

Mannesmann DKC21.3

Бренд: Rexroth Indramat Страницы: 38

Бренд: Toky Страницы: 4

Бренд: OptoSupply Страницы: 4

Бренд: Smartgen Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды