Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 247 | Manualshive

Страница: 247 / 1153

background image

System Integration Unit (SIU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

6-72

Freescale Semiconductor

6.3.1.89

Pad Configuration Registers 138–141 (SIU_PCR138–SIU_PCR141)

The SIU_PCR138–SIU_PCR141 registers control the function, direction, and electrical attributes of
ETPUA[24:27]_IRQ[12:15]_GPIO[138:141]. Only the output channels of ETPUA[24:27] are connected.

Figure 6-88. ETPUA[24:27]_IRQ[12:15]_GPIO[138:141]

Pad Configuration Registers (SIU_PCR138–SIU_PCR141)

Refer to

for bit field definitions.

lists the PA fields for

ETPUA[24:27]_IRQ[12:15]_GPIO[138:141].

6.3.1.90

Pad Configuration Registers 142–144 (SIU_PCR142–SIU_PCR144)

The SIU_PCR142–SIU_PCR144 registers control the function, direction, and electrical attributes of
ETPUA[28:30]_PCSC[1:3]_GPIO[142:144]. Only the output channels of ETPUA[28:30] are connected.

Figure 6-89. ETPUA[28:30]_PCSC[1:3]_GPIO[142:144]

Pad Configuration Register (SIU_PCR142–SIU_PCR144)

Address: Base + 0x0154 through Base + 0x015A

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

PA

OBE

1

1

When configured as ETPUA[24:27] or IRQ[12:15], the OBE bit has no effect. The OBE bit must be set to 1 for GPIO[138:141]
when configured as output.

IBE

2

2

When the pad is configured as an output, set the IBE bit to 1 to show the pin state in the GPDI register. Clear the IBE bit to 0
to reduce power consumption. The IBE bit must be set to 1 for GPIO[138:141] when configured as input.

0

0

ODE

HYS

SRC

WPE

WPS

W

RESET:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

U

3

3

The weak pullup/down value at reset for ETPUA[24:27] is determined by WKPCFG.

Table 6-83. PCR138–141 PA Field Definition

PA Field

Pin Function

0b00

GPIO[138:141]

0b01

ETPUA[24:27]

0b10

IRQ[12:15]

0b11

ETPUA[24:27]

Address: Base + 0x015C through Base + 0x015E

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

PA

OBE

1

1

When configured as ETPUA[28:30] or PCSC[1:3], the OBE bit has no effect. When GPIO[142:144] is configured as output, set
the OBE bit to 1.

IBE

2

2

When the pad is configured as an output, set the IBE bit to 1 to show the pin state in the GPDI[142:144] registers. Clear the
IBE bit to 0 to reduce power consumption. The IBE bit must be set to 1 for GPIO when configured as input.

0

0

ODE

HYS

SRC

WPE

WPS

W

RESET:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

U

3

3

The weak pullup/down value at reset for ETPUA[28:30] is determined by WKPCFG.

«
...
245
246
247
248
249
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: UniKey Страницы: 20

Бренд: Calsense Страницы: 74

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: B&G Страницы: 19

Бренд: Elby Designs Страницы: 4

HmIP-FAL230-C10

Бренд: HomeMatic Страницы: 42

Бренд: TEL Страницы: 26

Бренд: Vimar Страницы: 32

Бренд: Sentiotec Страницы: 45

Wired Manager - DALI

Бренд: Encelium Страницы: 8

Бренд: OMEGA AIR Страницы: 12

KaDe KDH-KZ620U

Бренд: AAT Holding Страницы: 28

Verifi FingerTouch Security

Бренд: Zvetco Biometrics Страницы: 8

Бренд: Trikdis Страницы: 7

total control MRX-10

Бренд: Universal Remote Control Страницы: 16

Бренд: DIG Страницы: 16

Бренд: Harsen Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды