manualshive.com logo in svg

Freescale Semiconductor MC68HC08KH12, Техническое описание

Поделиться
Скачать
Freescale Semiconductor MC68HC08KH12 Скачать руководство пользователя страница 223

MC68HC(7)08KH12

 — 

Rev. 1.1

Advance Information

Freescale Semiconductor

223

 

15.4.1 Port-D Keyboard Interrupt Functional Description

Writing to the KBDIE7–KBDIE0 bits in the keyboard interrupt enable 
register independently enables or disables each port D pin as a 
keyboard interrupt pin. Enabling a keyboard interrupt pin in port-D also 
enables its internal pullup device. A logic 0 applied to an enabled 
keyboard interrupt pin latches a keyboard interrupt request.

A keyboard interrupt is latched when one or more keyboard pins goes 
low after all were high. The MODED bit in the keyboard status and 
control register controls the triggering mode of the keyboard interrupt.

•

If the keyboard interrupt is edge-sensitive only, a falling edge on a 
keyboard pin does not latch an interrupt request if another 
keyboard pin is already low. To prevent losing an interrupt request 
on one pin because another pin is still low, software can disable 
the latter pin while it is low.

•

If the keyboard interrupt is falling edge- and low level-sensitive, an 
interrupt request is present as long as any keyboard pin is low.

If the MODED bit is set, the keyboard interrupt pins are both falling edge- 
and low level-sensitive, and both of the following actions must occur to 
clear a keyboard interrupt request:

•

Vector fetch or software clear — A vector fetch generates an 
interrupt acknowledge signal to clear the interrupt request. 
Software may generate the interrupt acknowledge signal by 
writing a logic 1 to the ACKD bit in the keyboard status and control 
register KBDSCR. The ACKD bit is useful in applications that poll 
the keyboard interrupt pins and require software to clear the 
keyboard interrupt request. Writing to the ACKD bit prior to leaving 
an interrupt service routine can also prevent spurious interrupts 
due to noise. Setting ACKD does not affect subsequent transitions 
on the keyboard interrupt pins. A falling edge that occurs after 
writing to the ACKD bit latches another interrupt request. If the 
keyboard interrupt mask bit, IMASKD, is clear, the CPU loads the 
program counter with the vector address at locations $FFEA and 
$FFEB.

Содержание MC68HC08KH12







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды