FREERIDER X2 HUB Скачать руководство пользователя страница 16

The following table will help you identify and correct common problems that can occur with an E -scooter.

15. Errors

15

The light on the
charger switches 
to green immediately.

TThe batteries are already charged. Some 

models are delivered fully loaded.

The charger's broken.

However, charge the battery for another four 

hours before using the scooter for the first time.

Replace the charger.

Symptoms

No function at all.

The device does not
 move, although the
 gas lever was
 pressed.

The device only runs 
periodically or very 
slowly.

The device fails 
abruptly while
driving.

The batteries can no
longer be charged or
will not last much
longer

Possible reasons

Solutions

The fuse was not used or defective.

The battery pack is not or is not properly 

connected.

The stand didn't go up.

The stand didn't go up.

The gas handle is faulty or not correctly 

connected.

The batteries can't be recharged anymore.

The batteries have reached the end of their life.

Brake levers are engaged.

The brake handle breaker is defective.

The batteries are not fully charged or have a 

polarity problem.

The engine or control unit is overheated.

The connectors have a wavelength contact.

The brake arches are not correctly adjusted and 

release the brake contact.

The engine ran hot.

Batteries have reached the end of their life or 

poor polarity among themselves. These should 

be replaced by a new battery pack.

The charger is no longer functioning properly.

The connection cable from the charging box to 

the control unit is no longer properly connected.

The controller is defective

The fuse on the battery pack is defective (if LED 

is off).

Knock on the stand.

Check the gas handle, wiring and replace it if 

necessary.

The connectors may have been switched when 

commissioned. Watch out for the right 

countersign.

Replace the batteries or the charger.

Replace the batteries.

Release the brake.

Replace the brake handle

Reload the batteries or replace them.

Wait about 15 -minute cooling time. Do not use 

full throttle for a while.

Check all connections to the correct seat.

Set the bow line precisely.

Let the engine cool down. Avoid extreme climbs 

when the speed decreases vehemently and 

only reaches step speed.

Please contact your dealer.

Replace the fuse.

Replace the batteries.

Replace the charger.

Check the connection of the charger and cable 

in the battery compartment, as well as the fuse.

Put the fuse on.

Connect the shopping bag according to 

instructions.

Knock on the stand.

Содержание X2 HUB





















Отзывы: