background image

3

IMPORTANT SAFETY INFORMATION

THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY

READ ALL INSTRUCTIONS BEFORE USING THIS TREADMILL

CAUTION:

Before starting any exercise program, it is recommended that you consult your physician.

WARNING:

Connect this unit to a properly grounded outlet only.

DANGER:

To reduce the risk of electric shock, always unplug the treadmill from the electrical outlet immediately after

using and before cleaning.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons

:

1.  Use 120 volt a.c. household current on a dedicated circuit.

Grounding Instructions

This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the
risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.  See diagram below for grounding
methods.

 2.  It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and

precautions.

3.  The use of an extension cord with this product is not recommended.  If an extension cord is needed, use a short (less than 10

feet) heavy gauge (14 gauge or better) extension cord with a three prong (grounded) plug and receptacle.

4. Never leave the treadmill unattended when plugged in.  Remove the safety key and unplug the unit from the outlet when not in

use and before removing or replacing parts.

5.  Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or

exposed to water.  Never move the treadmill belt while the power is turned off.

6.  Do not pull the treadmill by the power supply cord or use cord as a handle.  Keep cord away from heated surfaces and open

flames.

7.   Fitness equipment must always be installed and used on a flat surface.  Do not use outdoors or near water.  Do not place the unit

on a loose rug or uneven surface.  It is recommended to use an equipment mat to prevent the unit from moving while it is being
used, which could possibly scratch or damage the surface of your floor.  It is recommended to have a minimum of 3 metres safe
clearance on all sides of the treadmill while in use.

8.  Keep the treadmill indoors, away from moisture and dust.  Do not put the treadmill in a garage, covered patio or near water.
9.  Do not operate the treadmill where aerosol products are used or where oxygen is being administered.
10. Read, understand and test the emergency stop procedure before using the treadmill (see operation and adjustment on page 10)
11. Do not insert any objects into any openings.
12. Inspect and properly tighten all parts of the treadmill regularly.
13. Keep children and pets away from this equipment at all times while exercising.
14.Handicapped individuals should have medical approval and close supervision when using this treadmill.
15. Do not place hands or feet under the treadmill.  Always keep hands and legs off of the treadmill when others are using it.
16. Never turn on treadmill while standing on treadbelt.   Always hold the handrails while using the treadmill.  Always return the

treadmill to the slowest speed to provide for safe dismount and low speed restart.

17. To disconnect, turn all controls to the off position, then remove plug from outlet.
18.Do not attempt to raise, lower or move the treadmill until it is properly assembled. See assembly on page 7 and to fold and move

the treadmill on page 17.  Care must be taken when lifting or moving the equipment, so as not to injure your back.  Always use
proper lifting techniques.  You must use any attachments that are not recommended by the manufacturer.

Содержание C 249 30087 0






































Отзывы: