manualshive.com logo in svg

FRC InControl TGA300, Руководство пользователя

Поделиться
Скачать
FRC InControl TGA300 Скачать руководство пользователя страница 36

TGA300 Rev180405

36

Ford Harness Connections

J1939 Interface Information

A J1939 CAN input is required to provide engine information to the governor. The 

Ford vehicle CAN Bus information needs to be interpreted. A J1939 Translator Module 

with a harness to connect it to the ODB-II connector must be installed.

Note:

 The ODB-II connector and wiring is accessed under the dash.

There are two scenarios:

I.  The J1939 Translator Module is installed as a component with governor kit 

(no Seat Belt Monitoring System is installed).

Install the J1939 Translator Module and the ODB-II interconnecting harness 

(provided with the governor kit). A 2-Pin connector is provided for the wires to 

governor.

II. The J1939 Translator Module is installed as part of the NFPA1901 compliant 

Seat Belt Monitoring and VDR System.

The Translator Module/ODB-II/VDR harness is under the driver side dash. 

A T-cable (provided with the governor kit) needs to be installed at the 4-Pin 

connector that is between the harness and the VDR.

Stationary Elevated Idle Control (SEIC) Interface Information

Note:

 Access wires for SEIC are located in cabin, tagged and bundled above 

the parking brake pedal assembly behind datalink connector.

SEIC is used in two modes: stationary and split shaft. The governor provides a 

variable RPM control to the Ford Power train Control Module (PCM) when all enabling 

conditions are met. Refer to Figure 14 Ford TGA306/406 PCM Wiring.

SEIC Enablers:

 Parking brake applied; Foot off of service brake; Vehicle in 

park; Foot off of accelerator pedal; Vehicle speed is 0 mph (stationary); Engine 

at a stable base idle speed.

Note:

 Do not press the accelerator or service brake pedal when engaging the 

fire pump, this prevents the switch into SEIC (Stationary Elevated Idle 

Control).

Содержание InControl TGA300





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды