background image

13 

 

 
 
 
 

HEAVY METAL REDUCTION SYSTEM LIMITED WARRANTY 

 
 

What Does This Warranty Cover? 
This warranty covers any defects in materials and workmanship of the Heavy Metal Reduction System when 
installed and operated within recommended parameters, with the exceptions stated below.

 

 
How Long Does The Coverage Last? 
The manufacturer will warrant its Heavy Metal Reduction System, for a period of one year from the date of 
purchase. All implied warranties including merchantability and fitness for a particular purpose are limited to one 
year from the date of purchase for the Heavy Metal Reduction System. Some states do not allow limitations on 
how long an implied warranty lasts, so the above limitations may not apply to you.

 

 
What Will The Manufacturer Do? 
The manufacturer will repair or replace at its discretion any defective component. You must pay any labor 
charges. You must also pay for shipping or travel charges to return the defective part(s).

 

 
What Does This Warranty Not Cover? 
The above warranty will not apply to any part of the Heavy Metal Reduction System that is damaged because 
of neglect, misuse, alterations, accident, misapplication, physical damage, or damage caused by fire, acts of 
God, freezing or hot water or similar causes. Consequential and incidental damages are not recoverable under 
this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so 
the above limitation or exclusion may not apply to you.

 

 
We recommend that you use only the manufacturer's replacement parts since improper parts or incorrectly 
performed maintenance or repair voids this warranty. 

 

 
How Do You Get Service? 
In order to be eligible for service under this warranty you must (a) contact your local dealer who supplied the 
unit.

 

 
How Does State Law Apply? 
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

 

 
 
 
 
 
 
 

Содержание HMX-1














Отзывы: