Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 86

Страница: 86 / 156

COMMUNICATIONS

FE Connect for Cerus X-Drive Mobile Application

Using the Mobile App

Use the following procedure to program an X-Drive that has been paired with the app.
1.

On the

My Products

screen, tap the name of the desired drive to connect to the device and enter the

Dashboard.

2. Tap the

button to for a list of options.

3. Tap

Setup

to change VFD settings, then tap

All Settings

to display the complete parameters lists.

4. From here, you will be able to program and verify all drive settings. Refer to

“Setting Operating Param

eters” on page 48

for more information about settings.

When setup programming is complete, many more features are available within the app for both controlling
the drive and fine tuning its performance.
1.

Drive Info display

2. Reports Generator screen
3. Dashboard display. Use the Control Mode slider at the bottom to switch control of the drive between

the keypad and the mobile app.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды