5
The heating tank must be positioned horizontally. Ensure the tank
is positioned correctly, following the instructions on the label.
Flush the heating tank 3 times within one hour before bringing
it into service.
Important note:
If, during the heating-up period,
water does not start to discharge into the tundish within 4 minutes,
switch off the power immediately and open the boiling water tap to
release the pressure. Consult the troubleshooting guide.
12
Affix the supplied data plate close to the unit or on this manual.
This will provide easy access to ascertain the model and serial
number of the unit even if you decide to place the unit behind the
plinth of the cupboard.
13
You have successfully completed the installation of your Franke
Heating Tank.
14
Finally. Please demonstrate to the homeowner the procedure for
replacing the water filter cartridge.
Resetting the thermal cut-out
The tank is fitted with a safety device that will shut-off the boiling
water if the tank is switched on without water, or there is a power
surge. The hot water flow can be restored by operating a reset button,
located behind a white plastic cover, on the front of the tank (opposite
side to where the braided inlet and outlet hoses are connected).
Disconnect the tank’s electrical power supply. Operate
the boiling water handle on the tap to check that the tank is full of
water. Use a small screwdriver to remove the white cover to reveal
the button in the recess. Press the button firmly with the flat end of a
pencil until you hear a click to reset the tank. Replace the white cover.
Switch on the power supply and allow 20 minutes for the tank to
reheat before use.
Drain
Disconnect the electricity supply to the tank. Operate the boiling
water function until only cold water flows from the spout. Shut off the
water supply to the tank at the main stopcock or use the stop valve
on the pressure relief valve. Operate the boiling water function again
to release the pressure in the heating tank. Turn it off once the water
stops flowing. Disconnect the pipes from the heating tank. Remove
the tank carefully and pour out the water it contains.
7
Connect the cold water hose from the heating tank to the Inlet
Pressure Relief Valve (4). The flexible connecting hoses must not be
twisted or kinked once connected. Note Do not overtighten the nut.
8
You must now install your Minerva tap following the instructions
in the manual supplied. You will need the Sealing ring (8) and the
Compression Rings (9) to install the boiling water tap.
9
Once the installation is complete, turn on the mains water supply
and open the valve on the Inlet Pressure Relief Valve. In order to
fill the water heater tank, you first need to fully open the tap. Flush
the heater through for 3 minutes until clear water comes out of the
tap. After turning the tap off, check all connections for leaks.
Important note:
Do not over-tighten the nut.
10
Install the filter cartridge in the filter housing. Refer to the separate
Cartridge Change Instructions in the filter box.
11
Connect the plug of the water heater to a wall socket. Now you can
switch on the main electrical supply. If necessary, also switch on
the electrical supply of the heating tank. It will take approximately
20 minutes for the water in the tank to reach full temperature.
Once heated, flush the heating tank again for 3 minutes.
6
You can fit the heater (1) behind the plinth, providing the plinth
is no less than 150mm (a) or in the kitchen cupboard (b). Both
installations need a level and vibration-free surface. Installation
option (a) fit the heater behind the plinth. Route the mains lead
and connecting hoses upwards behind the floor and backboard
of the cabinet. Alternatively drill a 60mm hole in the base of the
cabinet and route hoses and mains lead through hole. Installation
option (b) Position the heater in the back of the cupboard.
A
B
DEZE ZIJDE BOVEN
Optie A
THIS SIDE UP
Option A
CE CÔTÉ VERS LE HAUT
Option A
ok
X
CLICK
