8
036865-004
0112
9
0112
036865-004
MODULAR SPORTS BOTTLE FILLER
InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,
KEM8SBF, KEM12SBF
MODULAR SPORTS BOTTLE FILLER
InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,
KEM8SBF, KEM12SBF
STEP 9: UV KIT - InSTALLATIOn GUIDE (BAcK VIEW WITh chILLER,
UV, AnD FILTER)
a) Remove lower and upper front panels, if needed.
b) Screw UV housing clip to frame (only one clip required). Holes provided
in frame upper left side (
Figure 9 - BACK vIEW
).
c) Install inter connecting water fitting to UV housing, provided. Refer to
Figure 10 and 11
for details.
d) Install quartz sleeve with O-Ring into UV housing. Assemble retainer
nut - do not over tighten refer to
Figure 10
for details.
e) Run UV power cord connection through hole provided in frame. Connect
UV bulb to power supply cord and insert bulb into UV housing. See
Figure
9 and 10
for details.
STEP 10: UV KIT - InSTALLATIOn GUIDE
a)
CAUTION
- Carefully swap UV housing into clip installed in STEP 9.
The UV bulb and quartz sleeve are made of glass and are fragile.
Use
CAUTION
in this step to avoid damaging these parts.
b) Connect all interconnecting water lines. See water circuit illustration on
next page.
c) Re-connect electrical power and install upper and lower front panels.
INLET
OUTLET
UV
INLET
OUTLET
HOLE PROVIDED
FOR ELECTRICAL
AND WATER RUN
FILLER DELIVERY TUBE
SOLENOID VALVE
SEE FIG. 11
FOR DETAILS
UV HOUSING
QUARTZ SLEEVE
AND O-RING
RETAINER NUT
UV LAMP
POWER SUPPLY
AND CONNECTOR
1/4" X 3/8"
REDUCER
3/8" X 1/2"
REDUCER
1/2" X 1/2"
ELBOW
INLET
OUTLET
UV
INLET
OUTLET
HOLE PROVIDED
FOR ELECTRICAL
AND WATER RUN
FILLER DELIVERY TUBE
SOLENOID VALVE
SEE FIG. 11
FOR DETAILS
UV HOUSING
QUARTZ SLEEVE
AND O-RING
RETAINER NUT
UV LAMP
POWER SUPPLY
AND CONNECTOR
1/4" X 3/8"
REDUCER
3/8" X 1/2"
REDUCER
1/2" X 1/2"
ELBOW
INLET
OUTLET
UV
INLET
OUTLET
HOLE PROVIDED
FOR ELECTRICAL
AND WATER RUN
FILLER DELIVERY TUBE
SOLENOID VALVE
SEE FIG. 11
FOR DETAILS
UV HOUSING
QUARTZ SLEEVE
AND O-RING
RETAINER NUT
UV LAMP
POWER SUPPLY
AND CONNECTOR
1/4" X 3/8"
REDUCER
3/8" X 1/2"
REDUCER
1/2" X 1/2"
ELBOW
A
AA
BB
B
SOLENOID VALVE
PROVIDED. SEE FIG.
2 IN STEP 2 OF THESE
INSTRUCTIONS.
BALL VALVE AND
3/8" O.D. COPPER
TO BUILDING
WATER SUPPLY.
FILTER ASSEMBLY
(OPTIONAL)
ATTACHED TO FILLER
DELIVERY TUBE. SEE
FIG. 2 IN STEP 2 OF
THESE INSTRUCTIONS.
REMOTE CHILLER
(OPTIONAL)
UV HOUSING
AND BALLAST
NOTE:
IF OPTIONAL FILTER ASSEMBLY IS NOT INSTALLED,
CONNECTION "
A
" WILL CONNECT TO LOCATION "
AA
" OF
THE UV ASSEMBLY.
IF OPTIONAL REMOTE CHILLER IS NOT INSTALLED,
CONNECTION "
B
" WILL CONNECT TO LOCATION "
BB
" OF
THE UV ASSEMBLY.
UV KIT - WATER cIRcUIT
Figure 9
(BAcKVIEW)
Figure 10
Figure 11
