Fox Thermal Instruments FT3 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 26

Fox Thermal Instruments FT3 Скачать руководство пользователя страница 18

timer indicating how much time is left to finish the test. A “Please Wait”
message will be flashing on and off on line 2 during this test.

F1 F2 F3 F4

Upon test completion, the final CAL-V™ value will be displayed along with a
Pass/Fail message.

Performing the Zero CAL-CHECK™ Calibration Validation Test

The Zero CAL-CHECK™ test is a companion test to CAL-V™. Unlike CAL-V™,
which may be performed in the pipe and at process conditions, Zero CAL-
CHECK™ must be performed at zero flow to ensure a valid test result. This
test is used to confirm that the flow meter still retains its original NIST-
traceable calibration at zero flow and that the sensor is free of film or residue
tat may affect readings. The test takes less than 5 minutes to complete. At the
conclusion of the test, a Pass or Fail message will be displayed. Press

F4

at

the conclusion of the test to return to normal measuring mode or to terminate
the test.

Press

FLO (F2)

from the main menu. The display will show:

F1 F2 F3 F4

Press

DGN (F1).

The display will show:

F1 F2 F3 F4

Press

TST (F2).

The display will show:

FLOW PARAMETER 1

DGN UNT PRM EXIT

DIAGNOSTIC
SIM TST EXIT

18

Calibration Validation

OPERA

TION

Operation: Zero CAL-CHECK

™

CAL-V

™

Model FT3

CAL-V = 0.51
Passed OK

Zero CAL-CHECK

™

«
...
16
17
18
19
20
...
»

Содержание FT3



























Отзывы:

Нет отзывов