Fox Thermal Instruments FT3 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 26

Fox Thermal Instruments FT3 Скачать руководство пользователя страница 13

Now that the sensor is isolated in the chamber of the Packing Gland
Assembly, the FT3 meter is ready to either perform the Zero CAL-CHECK™
test or set the Field baseline for future tests.

When the meter has completed the test, be sure to open the shut-off valve,
slide the meter downward until the ferrule rests in the fittings, and tighten the
small nut of the fittings in order to seal the probe in the stream again.

Check to be sure the meter has returned to normal operation.

Starting the Field Baseline Set

After the meter has been installed and wired correctly (see the Fox FT3
Instruction Manual that came with the meter), power on the meter.
The meter should default to display #1. Press "

F1

" to program the meter.

Press

Yes (F1)

to set Parameters and you will be prompted to enter the

password. Use a Level 2 password (9111). The display will show:

F1 F2 F3 F4

Press

FLO (F2)

to go to the Flow Parameter 1 Menu.

F1 F2 F3 F4

Press

DGN (F1)

to go to the Diagnostic Test Menu.

F1 F2 F3 F4

Press

TST (F2)

to get to the Diagnostic Test Sub-Menu.

FLOW PARAMETER 1
DGN UNT PRM EXIT

SET PARAMETERS

I/O FLO DSP EXIT

DIAGNOSTIC

SIM TEST EXIT

13

Start Up

Calibration Validation

ST
ART UP

399 Reservation Road, Marina, CA 93933 Ph: 831.384.4300 Fax: 831.384.4312

Packing Gland

Assembly

Setting Field

Baseline

«
...
11
12
13
14
15
...
»

Содержание FT3



























Отзывы:

Нет отзывов