Four winns Horizon 200, Руководство пользователя

Страница: 29 / 140

Owner’s Manual
05/00
Section B
Page 7
The transducer is factory installed and is water tested. It
will be located in the bilge compartment to limit the effect
of water turbulence while underway.
NOTICE
DO NOT depend solely upon the depth sounder
for water depth. It is important to have
navigational charts of the waters in which you
are operating.
Do not rely on depth sounder to avoid sub-
merged objects. Depth sounders provide a rela-
tive indication of water depth only.
1. 1999 Models Four Winns/VDO Clock and Depth
Operation
The LCD display has two main functions, clock and
depth functions. The operation and display of the func-
tions is controlled by the SET and MODE push but-
tons. The programming of the VDO/FOUR WINNS
clock and depth operations of the new instrument mod-
ule is described in the following:
Changing from clock to depth is done by pressing both
SET and MODE and holding them for 2 seconds. Press-
ing and holding both buttons again will toggle back to
clock function.
When using single push buttons, you will need to hold
the button in for 1/3rd of a second before the button will
be accepted. This is to prevent accidental inputs while
the boat is in motion.
2. Depth & Alarm
In depth mode, the display normally shows the current
depth. If dashes are shown, the depth sounder is not
generating valid data. If the current depth is less than
the alarm depth, the up & down arrow heads will flash
and the horn will chirp rapidly.
While in normal depth display, pressing the MODE but-
ton will cause the alarm depth to be displayed. After 10
seconds, the display will return to depth, or pressing
MODE a second time will return to depth display.
If the alarm is on (chirping), when the alarm depth is
displayed (using MODE) the audio part of the alarm
will be disabled. Reentering the alarm display will re-
enable the audio alarm. The flashing arrows will indi-
cate an alarm condition whether the audio is on or off.
E. Voltmeter
The voltmeter monitors battery condition and thus al-
ternator performance. See Section E for additional
information on electrical systems.
On the Horizon and Sundowner cluster, the voltme-
ter indicates the voltage at the cluster. If the voltage
is below 10 or above 16.5 VDC (volts of direct cur-
rent) while the engine is running the telltale will light,
and the cluster will beep every 2 seconds.
F. Fuel Gauge
The fuel gauge displays the level of fuel that is present
in the fuel tank. The fuel gauge will operate when the
ignition switch supplying power to the fuel gauge is in
the RUN position. At 1/6 of a tank, a low fuel warning
light will appear on the module.
Due to the mechanical nature of the fuel sender, varia-
tions in readings during various speeds of operation
may occur. This system is merely a relative indication
of the available fuel supply and not a calibrated instru-
ment. Relative adjustments can be made by your Four
Winns dealer by bending the fuel sender float arm.
Refer to Section F-1e Fuel Sender for additional infor-
mation.
NOTICE
Use only clean fuel of the type and grade
recommended by the engine manufacturer.
The use of incorrect or contaminated fuel can
cause engine malfunction and serious dam-
age. Refer to Section F Fuel Systems for ad-
ditional information.
G. Power Trim Gauge
Boats equipped with stern drives also have a “power
trim gauge.” This gauge provides a visual indication
of the inward-outward (trim angle) position of the
outdrive. There is not a trailer travel mode on the
gauge.
H. Depth Sounder
The depth sounder is standard equipment on the Ho-
rizon and Sundowner models. Readings can be dis-
played in feet or meters. The depth sounder has both
audible and visual alarm. The Four Winns/VDO clock
and depth operation is included below.