F3x32 Series Router User Manual
Xiamen
Xiamen
Xiamen
Xiamen Four-Faith
Four-Faith
Four-Faith
Four-Faith Communication
Communication
Communication
Communication Technology
Technology
Technology
Technology Co.,Ltd.
Co.,Ltd.
Co.,Ltd.
Co.,Ltd.
Page 40 of 93
Add
:
J1-J3,3
rd
Floor,No.44,GuanRiRoad,SoftWare Park,XiaMen .361008.China
http
:
//www.fourfaith.com
Tel
:
+86 592-6300326
6300325
6300324
Fax
:
+86 592-5912735
CTS
CTS
CTS
CTS Protection
Protection
Protection
Protection Mode
Mode
Mode
Mode
:
The default value is disabled. When set to Auto, a protection mechanism
will ensure that your Wireless-B devices will connect to the Wireless-G router when many
Wireless-G devices are present. However, performance of your Wireless-G devices may be
decreased.
Frame
Frame
Frame
Frame Burst
Burst
Burst
Burst
:
The default value is disabled. Frame burst allows packet bursting which will
increase overall network speed though this is only recommended for approx 1-3 wireless clients,
Anymore clients and there can be a negative result and throughput will be affected.
Beacon
Beacon
Beacon
Beacon Interval
Interval
Interval
Interval
:
The default value is 100. Enter a value between 1 and 65,535 milliseconds. The
Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet
broadcast by the router to synchronize the wireless network. 50 is recommended in poor reception.
DTIM
DTIM
DTIM
DTIM Interval
Interval
Interval
Interval
:
The default value is 1. This value, between 1 and 255, indicates the interval of
the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing
clients of the next window for listening to broadcast and multicast messages. When the router has
buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a
DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and
multicast messages.
Fragmentation
Fragmentation
Fragmentation
Fragmentation Threshold
Threshold
Threshold
Threshold
:
This value should remain at its default setting of 2346. The range is
256-2346 bytes. It specifies the maximum size for a packet before data is fragmented into multiple
packets. If you experience a high packet error rate, you may slightly increase the Fragmentation
Threshold. Setting the Fragmentation Threshold too low may result in poor network performance.
Only minor modifications of this value are recommended.
RTS
RTS
RTS
RTS Threshold
Threshold
Threshold
Threshold
:
This value should remain at its default setting of 2347. The range is 0-2347 bytes.
Should you encounter inconsistent data flow, only minor modifications are recommended. If a
network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be
enabled. The router sends Request to Send (RTS) frames to a particular receiving station and
negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with
a Clear to Send (CTS) frame to acknowledge the right to begin transmission.
Max
Max
Max
Max Associated
Associated
Associated
Associated Clients
Clients
Clients
Clients
:
1-128.
AP
AP
AP
AP Isolation
Isolation
Isolation
Isolation
:
The default value is Off. This setting isolates wireless clients so access to and from
other wireless clients are stopped.
TX
TX
TX
TX Antenna/
Antenna/
Antenna/
Antenna/ RX
RX
RX
RX Antenna
Antenna
Antenna
Antenna
:
Values are Auto, Left, Right, default value is Auto. This is used in
conjunction with external antennas to give them optimum performance. On some router models
left and right antennas may be reversed depending on you point of view.
Preamble
Preamble
Preamble
Preamble
:
Values are Long and Short, default value is Long. If your wireless device supports the
short preamble and you are having trouble getting it to communicate with other 802.11b devices,
make sure that it is set to use the long preamble.
Wireless
Wireless
Wireless
Wireless GUI
GUI
GUI
GUI Access:
Access:
Access:
Access:
The default value is Enabled. The setting allows access to the routers
setup (GUI) from wireless clients. Disable this if you wish to block all wireless clients from
accessing the setup pages.