10
9
RANGE HOOD
■
Range Hood and Wall Cupboard Standard Combination Size Installation Diagram
(Unit: mm)
Hole Size of Cabinet on Top Surface
Installation diagram for the top decorative
cover pothook.
Blower outer cover bottom and cabinet bottom should be even.
■
Preparation before installation
2.Tool preparation
Please prepare the following tools before range hood installation.
(1).Impact electric drill (with drillbit of
φ
10mm )
(2).Cross screwdriver
(3).Internal hexagonal wrench (M6)
(4). Measuring tape
(5).Hammer
1.Warning, Please don’t make sundries into exhaust pipe to avoid damaging the range hood.
Estimate the exhaust pipe position. A straight and short exhaust pipe makes
smoke extraction more smooth, please refer to installation diagram.
The joint between exhaust pipe and wall hole should be sealed with tape, and ensure
firm connection between exhaust pipe and exhaust cover.
Too small wall hole will affect smoke extraction, therefore, please broaden the wall hole
to fit exhaust pipe size under safety condition.
Ceiling
Exhaust pipe
Fig.2
Fig.3
Fig.4
Fig.5
Fig.1
Installation Steps
1. Demount the two screws which is for fixing the blower outer
cover, take down the blower outer cover and decorative
cover. Reserve
φ
10mm drill bit for the impact electric drill.
2. Refer to Fig 1, set the right position on the wall to drill and
then firmly imbed the expansion pipe. Insert wooden
screws to tighten the fixed hook and decorative cover
hook; you can also use two ST3.9X9.5 self-tapping screw to
fix the decorative cover on the suspended ceiling.
3. Use eight M4×18 screws to fix the exhaust cover and sealing
ring on the top of appliance.
4. Use ST3.9X9.5 self-tapping screws to fix the exhaust pipe on
the exhaust cover.
5. Hang the hood firmly: face squarely- not slanting, side-
looking-the hood will tightly stick the wall and a little lacune.
6. Install the exhaust pipe according to Fig 1: check the pipe
shell is not bulging and not shriveled, curve freely. The
exhaust pipe and wall should be tightly connected to
prevent smoke back, the backflow barrier blade should be
up and down smoothly.
7. Confirm the churn drilling hole position according to Fig 2,
firmly imbed the expansion pipe, fix the safety block, and
screw in the wooden screw to fix.
8. Blower outer cover and decorative cover installation
(1) Put the decorative cover inside of the blower outer cover.
(2) Take up the blower outer cover and decorative cover
meantime; inject the decorative cover into its pothook,
then push the decorative cover and blower outer cover
along the pothook assembly to the end.
(3) After pushing the decorative cover and blower outer
cover to the end, the blower outer cover will slip down
slowly, and inject the blower outer cover buckle to the
blower rack, then insert the blower outer cover to the gap
a. Please take down the blower outer cover before
installation.
b. If you install the range hood matching with cabinet, then
exchange Step (4) and Step (5).
c. Please select right drill bit according to the drilling
place specific situation.
which is between top panel and blower rack.
54
54
186
665~940
127
Ø230
384
900
R115
535
900
127
Ø180
650
～
750
910
Exhaust pipe through cabinet
127
535
384
127
≥860
800
（
850
）
650
～
750
910
Ø180
Decorative
cover
Exhaust pipe through ceiling
800(850)
Exhaust pipe
Ceiling
Cupboard
186
54
54
602
657
335
335
400
400
≥680
80
80
Pothook
Decorative cover
267.5
542
650
～
750
186
54
54
Safety block
9. Installation of ring suction plate
(1) Hold the front side of the ring suction plate firmly with both
hands, and place the left and right pothooks on the rear side of
ring suction plate into the left and right hook racks of the smoke
collecting hood;
