Model D2424LV Reference Manual (Names and Functions)
13
15. Execute/Yes key
[EXECUTE/YES/CHASE]
Press this key to execute the operation when you
edit data on the hard disk using the edit functions
such as Paste and Erase, when you put the recorder
into SETUP mode, or when you set the parameters
in the SETUP menu.
Pressing this key while holding down the
[SHIFT]
key
allows you to select the Slave mode on/off.
* Refer to page “
68
” for more information about using
this key for the Paste or Erase operation.
* Refer to page “
107
” for more information about using
this key in SETUP mode.
* Refer to page "
82
", “
85
” for more information about
using this key for the Slave Mode operation.
14. Exit/No key
[EXIT/NO/EJECT]
The opposite of the
[EXECUTE/YES]
key, this key is
used to stop operation. When using a removable
type SCSI device for backup, if the "Drive setting" in
the SETUP mode is set to "
SCSI6
", the SCSI disk can
be ejected by pressing this key while pressing on
the
[SHIFT]
key when the SCSI disk is stopped.
11. Display Select key
[DISP SEL/TIME BASE SEL]
This key is used to change the display mode. Pressing
this key repeatedly will change the display mode as
follows:
* Refer to page "
25
" in regards to REMAIN, page "
107
"
on the SETUP menu, and the "
APPENDIX
" on details if
the Model 8346 TC/SYNC card is installed.
Pressing this key while holding down the
[SHIFT]
key
will switch the Time Base (*) as follows.
The Time Base can be set when the display shows
the recorder’s current position or the available disk
space (REMAIN).
* Refer to pages “
24
” and “
107
” for more information
about MTC and the internal Tempo Map.
(*) Time Base:
The recorder uses time display (ABS or MTC) or Bar/Beat/
Clock display to indicate the current position of the
recorder section. These displays are called “Time Base.”
ABS (Absolute Time) shows the absolute time of the disk,
and MTC (MIDI Time code) shows the relative time obtained
by adding an MTC offset value to the ABS value.
Bar/Beat/Clock (BAR/BEAT/CLK) indicates a position
within a piece of music and conforms to the MIDI clock
and Song Position Pointers created on the internal Tempo
Map.
10. Auto Return End key
[AUTO RTN END/PREVIEW]
This key is used to store and recall the end point
(AUTO RTN END point) for the Auto Return or Auto
Repeat operation. You can locate a stored AUTO
RTN END point. If you press the
[AUTO RTN END]
key while holding down the
[SHIFT]
key when the
recorder is stopped, you can preview the fade-out
part at the stored AUTO RTN END point.
* Refer to page “
55
” for locating the AUTO RTN END
point.
* Refer to page “
68
” for copying/moving data.
* Refer to page “
64
” for previewing data at the AUTO
RTN END point.
12. Program select key
[PGM SEL]
This key has the following two functions depending
on the setup condition of "
Chain Play?
" (Setup of the
Chain Play Mode) in the SETUP mode.
* Refer to page “
37
” for program select function.
13. Store key
[STORE/HOLD]
This key is for storing time figures (or measure/beat/
clock figure) in any memory key.
Following this key, when each memory key is
pressed, data shown in the display will be stored in
their respective memory key.
Using "
Press LOCATE: **
", which is shown after
pressing the
[RECALL]
key, if this key is pressed after
input of any number (00-99) in "
**
," it is registered
as time data for the specified locate number.
If this key is pressed while holding down on the
[SHIFT]
key, the currently shown time (BAR/BEAT/
CLK) will be held and this data can then be edited.
After editing, the time thus edited will be stored using
the procedure above.
* Refer to page “
51
” for registering in the memory key.
If an optional Model 8346 TC/SYNC card is installed,
information in the MTC IN or TC IN will differ
depending on "
Ref. TC?
" menu setting (MTC or LTC)
in the SETUP mode. If the card is not installed, "
00H
00M 00S 00F 00SF
" will always be displayed.
The current position
Disk space (remain)
MTC IN or TC IN display
ABS time base
Bar/beat/clk time base
MTC time base
<When the "Chain Play?"menu is set to other than "Off">
You can specify the program at executing chain play
when this key is pressed.
* Refer to page “
58
” for details on the chain play mode.
<When the "Chain Play?" menu is set to "Off">
The D2424LV will switch to setup of a new program
and the program select execution mode when this
key is pressed.
