5
4
6
7
1
2
3
Quick Installation Guide
Network Video Recorder
Model: FN3109H/FN3104H
V1.5
EQ310409
NVR
IR Remote Control (Only FN3104H)
Battery (Only FN3104H)
USB Mouse
DC Power Adapter
Screw Pack
Antistatic Gloves
Data Wire and Power Wire of the Hard Drives
Quick Installation Guide
CD
Warranty Card
Ethernet Cable
WARNING
Before installing a hard disk drive (HDD), please make sure the power
is disconnected from the NVR.
Find the antistatic gloves from the package of the NVR and wear the
gloves.
It is recommended that a hard drive be used in 7200 high-speed or
above.
Power cable
HDD
Data cable
It is recommended to use SATA type of hard disk for recording.
Note
1.
Remove the cover from the NVR by unfastening the screws on the
rear and side.
2.
Connect one end of the data cable and power cable to the
motherboard of NVR and the other end to the HDD.
3.
Place the HDD on the bottom of the device and then fasten the
screws on the bottom to fix the HDD.
4.
Re-install the cover of the NVR and fasten screws.
Internet users
IP Camera
Power Switch
Power Supply
HDMI Video Output
VGA Video Output
USB Interfaces
DC 12V
POWER
HDMI
VGA
LAN
USB
ALARM N1
1 2 3 4 NO C
Alarm IN Alarm OUT
Router
Internet users
Procedure
1.
Connect your display to one of the video outputs (VGA or HMDI
interface).
3.
Connect an external storage device to the USB interface of the NVR as
a backup.
4.
Connect a mouse to the USB interface.
5.
Connect an alarm input device and an alarm output device to the
alarm input interface and alarm output interface respectively.
2.
Some devices need to connect to your router using an Ethernet cable,
including the NVR, PC, IP Camera.
6.
Connect the power adapter to the power input port.
Foscam cameras and NVRs require good security practices
to safeguard your privacy. You should regularly change
your camera or NVR password which is 8-10 numbers,
letters, symbols combination.
You should update your camera or NVR regularly. Make
sure your camera or NVR has the latest firmware installed
for your specific model and better experience.
1.
Turn on the power switch on the rear panel.
After the NVR starts up successfully, the Power LED and HDD LED
indicators will turn green. The startup page is displayed on the screen.
2.
Login page.
Select the Language, Enter the
Username
and
Password
, then click
on the
Login
button.
Default username is
admin with no password
Package Contents
Security Warning
1
Before You Start
2
Hard Disk Installation
3.
For the initial log in, the system will prompt you to change your
username and password. Once done, click the
OK
button.
4.
After modifying the username/password, you will be taken to the
Setup Wizard
.
1.
Setting the time. If you don’t want to use the Setup Wizard next
time, uncheck the
Setup Wizard
checkbox. Click the
Next
button.
2.
Select the HDD you would like to use, then click the
Format Hard
Disk
button to set up the HDD. Note that this will delete all files on
the HDD.
Select a protocol depending on which IP Camera you have.
FOSCAM protocol: The High Definition(HD) IP Cameras for Foscam.
MJ protocol: The Standard Definition(SD) IP Cameras for Foscam.
ONVIF protocol: IP Cameras which support ONVIF protocol.
3.
You can add an IP Camera that is connected to the internet on the
NVR.
You can configure the following information for your IP Camera.
The Setup Wizard can walk you through some important settings on
the NVR.
Input a new username and new
password, then click OK.
1. Select Your IP Camera
2. Click
Add
3
Device Connection
4
Log In
5
Setup Wizard
Uncheck the checkbox
2. Click
Format Hard Disk
3. Click
Next
1. Select your HDD
Format Hard Disk
