English
INSTALLATION INSTRUCTIONS
In case of pressures over 5 BAR (~75 PSI), we
recommend to use a pressure reducer.
Before proceeding with the assembly, purge the
hot and cold water pipes so as to avoid the
accumulation of dirt and impurities that could
affect the function of the faucet.
FIG. 01
Remove the protection covers (1.A) using a
screwdriver. Use the plug (1.B) if necessary.
FIG. 02
Fit the faucet body (2.A) to the wall with the
two upper outlets pointing towards the flow
elements. Connect the hot water supply to the
left inlet and the cold water supply to the right
one.
FIG. 03
The depth of the wall niche must correspond
(
wall coating included
) to the tolerance given
by the MIN/MAX references given on the
plastic cover (3.A).
Once all connections have been carried out,
activate the faucet at the working pressure
(we recommend maintaining the water flow
for a few minutes so as to purge the system
from any debris and/or dirt inside the piping).
Temporarily remove the protection cover (3.A)
to check if there are leakages and if the system
works regularly, reinstall the protection cover
(3.A) and finish the external wall surface.
FIG. 04
Remove the protection cover (3.A) as shown
in FIG. 03. With a screwdriver fasten the stop
cocks (4.F) in clockwise direction, loosen the
fitting screw (4.E) using the proper wrench
and pull out the test plug (4.D). Insert the o-ring
(4.C) and the sleeve (4.B) on the thermostatic
body. Use a small quantity of the special grease
included to lightly lubricate the o-rings of the
thermostatic cartridge (4.A). Insert the cartridge
in the faucet housing carefully aligning the
positioning hole with the housing of the fitting
screw (4.E), then tighten the latter.
Warning!
Do not force the screw (4.E). Excessive
tightening can affect the correct function of the
system or damage it. The thermostatic cartridge
is equipped with a safety anti-scalding retainer
set at 100°F (38°C). For higher temperatures
push the button on the adjustment handle. In
case of hot or cold water pressure failure, the
flow will automatically stop. With a screwdriver
loosen the stop cocks (4.F) in anti-clockwise
direction.
FIG. 05
Remove the protection tape of the adhesive
sponge (5.D) and apply it on the back of the
plate (5.C). Fit the sliding flat washers (5.B) and
(5.A) on the plate (5.C) and install it on the
thermostatic body till it is flush to the wall.
FIG. 06
Control handles installation.
For the upper portion with the cartridge, follow
the instructions given below:
Fit the insert (6.L) on the bar of the cartridge
so as to obtain the correct alignment once the
handle (6.F) has been installed and lock using
the screw included (6.I). Fit the handle (6.F)
and tighten the grub screw (6.G). Complete by
positioning the finishing cap (6.H).
For the lower portion with the thermostatic
cartridge, follow the instructions given below:
fasten the peg (6.E) on the bar of the thermostatic
cartridge and install the handle (6.A) placing
the ring (6.D) in between without moving the
bar so as to not compromise the cartridge
calibration. Tighten the grub screw (6.B) and
place the finishing cap (6.C).
Water Supply
Recommended
Maximum
Minimum
Hot Water Temperature
65 C° (~150F)
80 C° (~175F)
15 C° (~60F)
Working Pressure
3 BAR (~45PSI)
5 BAR (~75PSI)
0.5 BAR (~7PSI)
FIG. 01
FIG. 02
FIG. 06
FIG. 03
FIG. 08
FIG. 04
FIG. 05
FIG. 07
Istruz. art. 7369100.indd 4-6
26/04/11 10:08
