manualshive.com logo in svg

Fortinet FortiGate FortiGate-5001A, Руководство по системе безопасности

Поделиться
Скачать
Fortinet FortiGate FortiGate-5001A Скачать руководство пользователя страница 9

Hardware installation 

FortiGate-5001A   Security System Guide
01-30000-0438-200800801

9

Hardware installation

Before use, the FortiGate-5001A board must be correctly inserted into an 
Advanced Telecommunications Computing Architecture (ACTA) chassis such as 
the FortiGate-5140, FortiGate-5050, or FortiGate-5020 chassis. 

Before inserting the board into a chassis you should make sure the SW-11 switch 
is set correctly.

In the available Advanced Mezzanine Card (AMC) double-width opening on the 
FortiGate-5001A-DW front panel you can install a supported FortiGate ADM 
module such as the FortiGate-ADM-XB2 or the FortiGate-ADM-FB8.

This section describes:

•

Changing FortiGate-5001A SW11 switch settings

•

FortiGate-5001A mounting components

•

Inserting a FortiGate-5001A board

•

Removing a FortiGate-5001A board

•

Resetting a FortiGate-5001A board

•

Installing and removing AMC modules

•

Troubleshooting

!

Caution: 

Because the FortiGate-5001A board does not support hot swapping AMC 

modules, the FortiGate-5001A board must be disconnected from power and the left handle 
opened before you install a FortiGate AMC module. See 

“Installing and removing AMC 

modules” on page 19

.

!

Caution: 

Do not operate the FortiGate-5001A board with an open AMC opening. For 

optimum cooling performance and safety, the AMC opening must contain an AMC slot filler 
or a FortiGate AMC module.

Содержание FortiGate FortiGate-5001A







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды