background image

Contents 

FortiGate-5001FA2-LENC   Security System Guide
01-30000-76602-20080606

3

Contents

Warnings and cautions .....................................................................................  2

FortiGate-5001FA2-LENC security system......................  5

Front panel LEDs and connectors ...................................................................  6

LEDs .............................................................................................................  6
Connectors....................................................................................................  7

Accelerated packet forwarding and policy enforcement ...............................  7

FA2 interfaces and active-active HA performance........................................  8

Base backplane gigabit communication .........................................................  8

Hardware installation.........................................................  9

RAM DIMMs ........................................................................................................  9
Installing SFP transceivers.............................................................................  10
Changing FortiGate-5001FA2-LENC jumper settings ..................................  11
Inserting a FortiGate-5001FA2-LENC board into a chassis.........................  13

Before inserting the FortiGate-5001FA2-LENC board in a chassis ............  14
Insertion procedure .....................................................................................  14

Removing a FortiGate-5001FA2-LENC board from a chassis .....................  17
Troubleshooting ..............................................................................................  18

FortiGate-5001FA2-LENC does not startup................................................  18
FortiGate-5001FA2-LENC cannot display chassis information...................  20

Quick Configuration Guide .............................................  21

Registering your Fortinet product .................................................................  21
Upgrading to High Encryption........................................................................  21
Planning the configuration .............................................................................  22

NAT/Route mode ........................................................................................  22
Transparent mode.......................................................................................  23

Choosing the configuration tool ....................................................................  23

Web-based manager...................................................................................  23
Command Line Interface (CLI)....................................................................  24

Factory default settings ..................................................................................  24
Configuring NAT/Route mode ........................................................................  25

Using the web-based manager to configure NAT/Route mode...................  25
Using the CLI to configure NAT/Route mode..............................................  26

Configuring Transparent mode ......................................................................  27

Using the web-based manager to configure Transparent mode .................  27
Using the CLI to configure Transparent mode ............................................  28

Upgrading FortiGate-5001FA2-LENC firmware.............................................  29
FortiGate-5001FA2-LENC base backplane data communication ................  30

Содержание FortiGate 5001FA2-LENC



































Отзывы: