TO DISABLE READY MODE
COLD START MODE
REMOTE START / ALARM DIAGNOSTICS
Insert the key
and turn it to
the ignition
(RUN/ON)
position.
Within 10
seconds
press and
release the
Valet switch
3 times.
The LED
will turn ON
solid and
remain ON.
STANDARD
• Open any door(s)
• Open the hood
• Disengage the parking
brake
WITH NEUTRAL
SAFETY SWITCH
• Transmission not in
neutral position
• Open the hood
• Disengage the parking
brake
Note : If the parking
lights flash 3 times when
Remote-Starting, Ready
Mode is not enabled.
READY MODE
REMOTE STARTER
Parking Light flashes (before starting) :
3x
Ready Mode disabled
4x
Valet Mode activated (The LED
is on)
5x
Hood open
Parking Light flashes (after starting) :
1x
Normal stop (Brake, Park Brake)
3x
Runtime expired or shut down by
Transmitter
4x
No tachometer signal
5x
Hood open
6x
Over crank threshold (8 sec-
onds)
ALARM DIAGNOSTICS
Parking Light flashes (after disarm) :
3x
Door open – zone 3
4x
Shock sensor – zone 4
5x
Hood open – zone 5
6x
Trunk open – zone 6
7x
Auxiliary IN– zone 7
8x
Tilt Sensor – zone 8
X INDICATES THE NUMBER OF TIMES
THE PARKING LIGHTS WILL FLASH
AVERTISSEMENT
The engine’s tachometer
signal must be detected by
the remote starter to operate
in a manual transmission.
Tachometer is connected
directly to the vehicle:
Option 20: Mode 1 or 3
- or -
Tachometer is obtained
Through the interface
module EVO-ALL or EVO-
CHR:Option 20: Mode 1 or 6
Make sure that
all doors are
closed and the
transmission is
in the NEUTRAL
position.
While the
engine is
running.
Engage the
parking
brake.
Release the
brake pedal.
NOTE
If the
parking
lights flash
3 timed:
Verify the
Tachometer
signal.
Remove the
key from the
ignition barrel.
The vehicle
will remain
running with the
Remote-Starter.
Exit the vehicle
and close all of
the doors.The
Remote-Starter will
stop running once
all the doors are
closed.
ANALOG TACH LEARNING (PURPLE WIRE)
READY MODE FOR NEUTRAL SAFETY SWITCH
WARNING
Press and release 20 times the
valet-switch. The park-lights will
flash and the horn/siren will chirp
once to confirm.
X20
A long chirp indicates
tach learning failed. If
the procedure fails or
to re-learn the tach
setting, re-start the
procedure.
MULTI-
LINK
PROGRAM REMOTE-STARTER
OPTIONS WITH ONE CLICK
The MULTI-LINK displays diagnostic
information and changes the remote-
starters programming options.
IGN
START
OFF
4
Press and release
the brake-pedal
once.
5
READY MODE FOR NEUTRAL SAFETY SWITCH
START
Start the engine
with the key.
1
2
3
TACH LEARNING
1
Make sure that the
transmission is in the
NEUTRAL position.
3
Press and hold
the valet-switch until the
LED flashes, then release.
Engage the parking
brake.
2
MULTI-LINK
Remove the key from the
ignition barrel.The vehicle is
ready to start. (and not running)
NOTE: This feature will be functional only if the Tach is detected by a bypass module or
connected directly to the vehicle.
ENTER/EXIT VALET MODE
Press and release 20 times the
valet-switch. The park-lights will
flash and the horn/siren will chirp
once to confirm.
X20
A long chirp indicates
tach learning failed. If
the procedure fails or
to re-learn the tach
setting, re-start the
procedure.
MULTI-
LINK
PROGRAM REMOTE-STARTER
OPTIONS WITH ONE CLICK
The MULTI-LINK displays diagnostic
information and changes the remote-
starters programming options.
IGN
START
OFF
4
Press and release
the brake-pedal
once.
5
READY MODE FOR NEUTRAL SAFETY SWITCH
START
Start the engine
with the key.
1
2
3
TACH LEARNING
1
Make sure that the
transmission is in the
NEUTRAL position.
3
Press and hold
the valet-switch until the
LED flashes, then release.
Engage the parking
brake.
2
MULTI-LINK
Remove the key from the
ignition barrel.The vehicle is
ready to start. (and not running)
NOTE: This feature will be functional only if the Tach is detected by a bypass module or
connected directly to the vehicle.
Press and release 20 times the
valet-switch. The park-lights will
flash and the horn/siren will chirp
once to confirm.
X20
A long chirp indicates
tach learning failed. If
the procedure fails or
to re-learn the tach
setting, re-start the
procedure.
MULTI-
LINK
PROGRAM REMOTE-STARTER
OPTIONS WITH ONE CLICK
The MULTI-LINK displays diagnostic
information and changes the remote-
starters programming options.
IGN
START
OFF
4
Press and release
the brake-pedal
once.
5
READY MODE FOR NEUTRAL SAFETY SWITCH
START
Start the engine
with the key.
1
2
3
TACH LEARNING
1
Make sure that the
transmission is in the
NEUTRAL position.
3
Press and hold
the valet-switch until the
LED flashes, then release.
Engage the parking
brake.
2
MULTI-LINK
Remove the key from the
ignition barrel.The vehicle is
ready to start. (and not running)
NOTE: This feature will be functional only if the Tach is detected by a bypass module or
connected directly to the vehicle.
Press and hold the valet
switch until the Parking
lights turn ON, the
horn/siren will chirp.
Press and release the
TRUNK button, within 12 seconds
simultaneously press and hold the
LOCK and
START
buttons for 1 second. The remote’s Green LED will flash and beep
once to confirm. The parking lights will flash once.
TO DISABLE
• Press and release the TRUNK button, within 12 seconds
simultaneously press and hold the LOCK and START buttons for
1 second. The remote’s Green LED will flash and beep once to
confirm. The parking lights will flash twice.
• Put the Remote-Starter/alarm into Valet
• Remote-Start the vehicle
• Open the hood
• Press the brake pedal
• Turn the key to the ignition position.
• Disable Ready Mode (manual transmission).
Push the
START button
(3sec.). The
parking lights
will flash once
and then
remain on.
Press the START
button (3sec.) the
horn/siren will chirp 3
times to confirm tach
learning.
ONE
ONE
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either damage to the vehicle itself or to
the remote-starter module. This module must be installed by a certified technician including all of the supplied safety devices. Please note that this guide has been written for
trained professional technicians, a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the main unit must be cut.
Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle is in the “drive” or “reverse” position. If an automatic
transmission vehicle starts when the transmission is in gear, ensure that the safety wire loop on the unit is not cut. Once the safety wire loop is cut, the system is considered
an automatic transmission remote-starter indefinitely. Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is install on a manual
transmission vehicle.Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects.
This module must be install by qualified technician. This instruction guide may change without notice. To
download the installation guide, user guide, or the latest quick installation guide, visit:
www.fortin.ca
Technical support:
TEL: 514-255-4357
1-877-336-7797
Technical support:
TEL: 514-255-4357
1-877-336-7797
www.fortin.ca
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either damage to the vehicle itself or to
the remote-starter module. This module must be installed by a certified technician including all of the supplied safety devices. Please note that this guide has been written for
trained professional technicians, a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the main unit must be cut.
Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle is in the “drive” or “reverse” position. If an automatic
transmission vehicle starts when the transmission is in gear, ensure that the safety wire loop on the unit is not cut. Once the safety wire loop is cut, the system is considered
an automatic transmission remote-starter indefinitely. Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is install on a manual
transmission vehicle.Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects.
This module must be install by qualified technician. This instruction guide may change without notice. To
download the installation guide, user guide, or the latest quick installation guide, visit: www.fortin.ca
