Forster Products Co-Ax Скачать руководство пользователя страница 7

 

7.3 

Prime Your Cartridges 

 

NOTICE 

Wear thin medical gloves on the primer hand to improve 
the grip and help keep the primer from contamination. 

 

1.  Insert the primer on the Primer Seater Assembly and 

the case on the Top Shell Holder Jaws following the 
instructions below.  

 

 

WARNING

 

PERSONAL INJURY 

Ensure you use one of the two following positions for 
inserting the primers on the Primer Seater Assembly and 
the cases on the Top Shell Holder Jaws: 
 

Right-handed users:  

  Facing the press, take a position to the right of the 

press. 

  Lower the handle forward approximately 90 degrees. 

  From the rear of the press, use your right hand to insert 

the primer and the left hand to insert the case.

 

 

Left-handed users:  

  Facing the press, take a position to the left of the press. 

  Lower the handle forward approximately 90 degrees. 

  From the rear of the press, use your left hand to insert 

the primer and the right hand to insert the case.

 

 

              Right-handed                       Left-handed 

 

Failure to comply with these instructions could result 

in death or serious injury.

 

 
2.  Raise the Co-Ax Press handle to seat the primer. Only a 

very small amount of force is needed. 

 
 
 
 
 
 

8.0 

MAINTENANCE 

  Use a good quality gun oil to lubricate moving parts, wipe 

all unpainted parts with oil to prevent rust. 

  When not in use, keep a protective cover, such as our 

028271-300 (see Table 2), over the Co-Ax Press. 

 

9.0 

ACCESSORIES 

 

Table 2. Accessories 

Order No. 

Description 

SH1000 

Short Handle for Co-Ax Press

 

In use

 

028271-300 

Protective Cover for Co-Ax Press (Press 
not included) 

 

 

 

10.0 

REPLACEMENT PARTS

 

Every product component is available individually. A 
complete list of component order numbers and prices is 
available on our website. Go t

forsterproducts.com

, then 

click on

 Components/Parts Price List. 

 

11.0 

VIDEO

 

Go to our 

Video Library 

(see Video Library link under 

RESOURCES 

on our homepage) to see videos of the Co-Ax 

Press.

 

 

12.0 

DISTRIBUTORS/RESELLERS

 

We recommend using our Resellers when ordering our 
products. Their experience and knowledge will help you 
select the best products that meet your specific 
requirements. In addition, they usually offer the best prices 
and convenient delivery options. 
 
To find a Reseller, go t

forsterproducts.com

, then click on 

Locate a Distributor/Reseller

. If your Distributor/Reseller 

cannot supply you, please contact Forster Products directly. 

Содержание Co-Ax









Отзывы: