Forster Products Co-Ax Скачать руководство пользователя страница 3

Страница: 3 / 8

6.0

CASE SIZING AND BULLET SEATING

6.1

Choose the correct lower shell holder for the caliber being sized/seated

•

Table 1 shows the three lower shell holders available for the Co-Ax Press.

•

Figure 3 shows how to use the on-line

FORSTER PRODUCTS TOOL SEARCH BY CARTRIDGE

to find which lower shell

holder to use with your particular caliber,

Table 1. Lower Shell Holder Specifications

Name

(Order

Number)

Description

Dimensions

“S” Lower

Shell Holder

Jaws

(001231)

Factory

installed on

the Co-Ax

Press with

large ends

aligned; ready

for reloading.

•

Spring-loaded; automatically open

and close on the case head when

the case is inserted in the die and

the Co-Ax Press handle is lowered

for full length resizing, allowing the

case to float. When the handle is

raised and the case is extracted

from the die, these jaws

automatically open and release

the case.

•

Set of two.

Small ends hold:

.343” to .422” rim

.343"

Large ends hold:

.468” to .562” rim

.468"

Side View

“LS” Lower

Shell Holder

Jaws

(001251)

Available

separately.

•

Accommodates a wide range of

very large and very small case

heads.

•

Spring-loaded; automatically open

and close on the case head when

the case is inserted in the die and

the Co-Ax Press handle is lowered

for full length resizing, allowing the

case to float. When the handle is

raised and the case is extracted

from the die, these jaws

automatically open and release

the case.

•

Set of two.

Small ends hold:

.312” to .375” rim

.312"

Large ends hold:

.531” to .625” rim

.531"

Side View

Large End

.065"

Small End

.070"

Lower Shell

Holder

Adapter

Plate

(AP1000)

Available

separately.

•

For use with those few calibers

that the “S” or “LS” Shell Holder

Jaws do not accommodate.

Requires a caliber-specific shell

holder (not available through

Forster Products).

•

Not spring-loaded.

•

Single plate.

Without Caliber-Specific

Shell Holder

With Caliber-Specific

Shell Holder

Case Rim Diameter Comparison

.312" to .375"

.343" to .422"

“S” Shell Holder Jaws

“LS” Shell Holder Jaws

.468" to .562"

.531" to .625"

300"

400"

500"

600"

Complete contact of shell holder to case - case held securely.

Incomplete contact of shell holder to case - case still held securely as determined by user.

Содержание Co-Ax









Результаты поиска

Содержание Co-Ax

Отзывы:

Forster Products Co-Ax, Инструкция пользователя, Страница: 3 / 8

Результаты поиска

Содержание Co-Ax

Отзывы: