Formula Air RVA1-NX-06 Скачать руководство пользователя страница 9

Страница: 9 / 14

User manual | RVA Rotary valves
www.formula-air. com

Spare parts

Code

Description

JCAB000028

Bearing for RVA rotary valve (all models)

JCAB000001

Set of rubber blades (6 pcs) for RVA1

JCAB000002

Set of rubber blades (6 pcs) for RVA2

JCAB000003

Set of rubber blades (6 pcs) for RVA3

JCAB000004

Set of rubber blades (6 pcs) for RVA4

JCAB000005

Set of rubber blades (6 pcs) for RVA5

JCAB000027

Felt seals kit for all RVA rotary valve (2 seal rings)

JEBB000001

Gearbox for motor 0,37kW

JEBB000002

Gearbox for motor 0,55kW

JEAA000005

Motor - IE2 - 0,37kW - 4Pole - 230/400V - 50Hz

JEAA000006

Motor - IE2 - 0,55kW - 4Pole - 230/400V - 50Hz

JCAB000006

Rotor complete with rubber blades RVA1 – NX -06

JCAB000007

Rotor complete with rubber blades RVA2 - NX -06

JCAB000008

Rotor complete with rubber blades RVA3 - NX -06

JCAB000009

Rotor complete with rubber blades RVA4 - NX -06

JCAB000010

Rotor complete with rubber blades RVA5 - NX -06

5. Rotation detector (optional)

The optional rotation detector is a detection system that controls if the rotation disk is turning. In case of rotation
failure, it sends a signal to a control panel.

CAUTION

Before any manipulation to the rotary valve, make sure that the motor is stopped and that all electrical

connections are disconnected.

NOTE

: all electrical manipulations should be performed by qualified personnel only.

5.1

Placing the rotation detector

Remove the rotation disk protection cover by untightening the bolts holding it on the rotary valve body.

Position

Description

Position

Description

Body

Motor and gear

Bearing housing

Bolt M5 x 10

Cover

Rotation detector

Rotation disc cover

Rotor and rubber blades

Detector holder

Bolts and washers M8

Rotation disc

Bolts, nuts & washers M8

Содержание RVA1-NX-06















Результаты поиска

Содержание RVA1-NX-06

Отзывы:

Похожие инструкции для RVA1-NX-06

Бренды по названию

Популярные бренды

Formula Air RVA1-NX-06, Руководство по обслуживанию

Результаты поиска

Содержание RVA1-NX-06

Отзывы:

Похожие инструкции для RVA1-NX-06

Бренды по названию

Популярные бренды