manualshive.com logo in svg

formlabs Fuse Sift, Руководство пользователя

Поделиться
Скачать
formlabs Fuse Sift Скачать руководство пользователя страница 25

Preparation and setup | 

25

4.5.7 

Installing the Wi-Fi antenna

Install the Wi-Fi antenna to connect the machine to a wireless network.
To install the Wi-Fi antenna, screw the Wi-Fi antenna onto the jack on the back of the unit, next 
to the power, USB, and Ethernet ports.

4.5.8 

Turning on
To turn on the machine:

1.  Plug the included power cable into the power port on the back of the unit and connect the 

power cable to a dedicated circuit. 

2.  Flip the breaker switch on the back of the Fuse Sift to the 

ON

 position to turn on the machine.

3.  As the Fuse Sift initiates, the Formlabs logo with a progress bar appears on the touchscreen, 

followed by the onboarding process. Follow the on-screen prompts to finish setting up the machine.

To turn off the machine, refer to section 

5.6.2 Turning off

.

4.6 

Setting up a network connection

For detailed guidance and visual assistance, visit 

support.formlabs.com

.

Connect the Fuse Sift to a secure network via Wi-Fi or Ethernet, providing it internet access for 
remote troubleshooting, sending diagnostic logs, and receiving firmware updates. The Fuse 
Sift can connect directly to a computer with a USB cable.

4.6.1 

Connecting with Wi-Fi

The Fuse Sift’s built-in Wi-Fi (IEEE 802.11 b/g/n) supports WPA/WPA2 security. Use the 
touchscreen to configure a wireless network connection.

To connect with Wi-Fi:

1.  Tap the wrench icon on the 

Home

 screen. The 

Settings

 screen appears.

2.  Tap 

Connectivity > Wi-Fi

. The 

Wi-Fi

 screen appears.

3.  Toggle 

Use Wi-Fi

 to 

ON

. The toggle turns blue.

4.  Tap the desired wireless network.
5.  If prompted, enter your network password and tap the checkmark to confirm.

4.6.2 

Connecting with Ethernet

The rear of the unit is equipped with a RJ-45 Ethernet (10BASE-T/100BASE-TX/1000BASE-T) 1000 Mbit 
LAN Port. Use a shielded Ethernet cable (not included): minimum Cat5, or Cat5e or Cat6 for 1000BASE-T.

To connect with Ethernet:

1.  Plug one end of the Ethernet cable into the Ethernet port on the back of the unit.
2.  Connect the other end of the Ethernet cable to your LAN.

4.6.3 

Connecting with a manual IP configuration

When connected to an active Ethernet connection or available wireless network, the Fuse Sift can 
be configured with a static IP address. Use the touchscreen to configure a manual IP connection.

To connect with Wi-Fi or Ethernet using a manual IP configuration:

1.  With an established Ethernet or available Wi-Fi connection, tap the wrench icon on the 

Home

 screen. The 

Settings

 screen appears.

2.  Tap 

Connectivity

. The 

Connectivity

 screen appears.

 °

For Wi-Fi networks, tap 

Wi-Fi

, then the desired wireless network. A new screen appears. 

Tap the 

Manual IP

 button in the lower-left corner. The 

Manual IP Settings

 screen appears.

 °

For Ethernet connections, tap 

Ethernet

. The 

Manual IP Settings

 screen appears.

3.  Toggle 

Use Manual IP

 to 

ON

. The toggle turns blue.

4.  Enter the appropriate 

IP Address, Subnet Mask, Default Gateway

, and 

Name Server

.

Содержание Fuse Sift



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды