manualshive.com logo in svg

Formax FD 280, Руководство оператора

Поделиться
Скачать
Formax FD 280 Скачать руководство пользователя страница 40

 

 

36 

 
 

NOTE 

When backing paper is pulled, tabs will peel at the 

PEEL PLATE until pulling is stopped. 

 
3.  Remove any tabs or debris from the peel point 

area 

4.  Turn the POWER SWITCH on. 

5.  Toggle ON/OFF until a tab advances to the peel 

point and the TAB READY light illuminates. 

 
If the backing paper tears 

after

 the drive roll, the 

backing paper may fall away from the FD 280 and 
tabbing will continue.  If the backing paper wraps 
around rolls in the threading path, tabbing may 
continue, but tab placement may not be accurate.  To 
continue tabbing accurately: 
 

WARNING

 

DO NOT PLACE FINGERS OR TOOLS BETWEEN 

OR NEAR MOVING PARTS. 

 
1.  Turn the POWER SWITCH off. 

2.  Secure the backing paper around the TAKE-UP 

SPINDLE with the CLIP.  You may need to pull the 
backing paper a little to reach the TAKE-UP 
SPINDLE. 

 

9.2  Incorrect 

Threading 

 
Threading a tab strip incorrectly can prevent tabbing.  
Three examples are listed below.  

See Sec. 6.1

 

 

  PEEL PLATE ASSEMBLY is not latched

. 

  The 

backing paper will pull the PEEL PLATE assembly 
out of its slot, tabs will peel in the wrong place, 
and the PEEL PLATE assembly will block any mail 
pieces entering the FD 280.   

  Backing paper is threaded under the DRIVE 

ROLL

. 

 The backing paper will pull backward and 

no tabs will peel. 

Содержание FD 280













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды