manualshive.com logo in svg

Formax FD 280, Руководство оператора

Поделиться
Скачать
Formax FD 280 Скачать руководство пользователя страница 39

 

 

35 

 
 

To clear mail pieces from the transport tray: 

 

WARNING

 

DO NOT PLACE FINGERS OR TOOLS BETWEEN 

OR NEAR MOVING PARTS. 

 
1.  Press the STOP switch quickly 

2.  Leave the heads in place. 

3.  Reverse the piece through the FD 280 by turning 

the transport rolls by hand.  Pull the jammed mail 
pieces out of the input area of the transport.  

4.  If the jam happens upstream from the tab heads, it 

may be necessary to remove the transport rolls.  
Each set of rolls is spring loaded and is mounted 
on a spring loaded shaft.  Release spring pressure 
and slide the entire roll assembly out of the 
machine by compressing the spring on the shaft 
and lifting the shaft out once one end is free from 
its mounting hole.  Note one mounting hole is 
shaped like s “D” to prevent the shaft from turning.  
Make sure to replace the shaft as you have 
removed it. 

 

 

WARNING

 

DO NOT PLACE FINGERS OR TOOLS BETWEEN 

OR NEAR MOVING PARTS. 

 
 

9.1.3  Torn Backing 

Paper 

If the backing paper tears 

before

 the drive roll, the  

FD 280 will stop tabbing but continue feeding.         
To start tabbing: 
 

WARNING

 

DO NOT PLACE FINGERS OR TOOLS BETWEEN 

OR NEAR MOVING PARTS. 

 
1.  Turn the POWER SWITCH off. 

2.  Thread the FD 280 from the point where the 

backing paper tore. (Refer to 

Section 6.1

.)   

Содержание FD 280













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды