Ford ST1137-A Скачать руководство пользователя страница 42

413-01-42

413-01-42

Instrument Cluster

DIAGNOSIS AND TESTING (Continued)

PINPOINT TEST X: THE BRAKE WARNING INDICATOR IS ALWAYS ON

Test Step

Result / Action to Take

X1

CHECK THE BASE BRAKE SYSTEM
• Verify that the base brake system is operating correctly.

Yes

Is the base brake system operating correctly?

GO to 

X2

.

No

REFER to Section 206-00.

X2

CARRY OUT THE INSTRUMENT INDICATOR LAMP CONTROL

ACTIVE COMMAND USING THE SCAN TOOL
• Key in ON position.

• Enter the following diagnostic mode on the scan tool: Instrument

Cluster Active Command.

• Select the instrument cluster warning lamps and chime

Yes

command. Trigger the all lamps command on and off. Observe

GO to 

X3

.

the brake warning indicator.

Does the brake warning indicator illuminate when

No

commanded on and turn off when commanded off?

GO to 

X10

.

X3

CHECK THE BRAKE WARNING INDICATOR WITH THE

PARKING BRAKE SWITCH DISCONNECTED
• Disconnect: Parking Brake Switch C306.

Yes

• Monitor the brake warning indicator with the parking brake

GO to 

X4

.

switch disconnected.

No

Does the brake warning indicator continue to illuminate?

INSTALL a new parking brake switch.

TEST the system for normal operation.

X4

DETERMINE IF GENERIC ELECTRONIC MODULE (GEM) IS

RECEIVING THE CORRECT PARKING BRAKE INPUT
• Monitor GEM PID PRK BRK with the parking brake switch

Yes

disconnected.

GO to 

X6

.

Does the PID read OFF?

No

GO to 

X5

.

X5

CHECK CIRCUITS 128 (VT/YE) AND 22 (LB/BK) FOR A SHORT

TO GROUND
• Key in OFF position.

• Disconnect: GEM C201d.

• Measure the resistance between the GEM C201d pin 4, circuit

128 (VT/YE), harness side and ground.

Yes

GO to 

X9

.

No

REPAIR the circuit. TEST the system for

Is the resistance greater than 10,000 ohms?

normal operation.

X6

CHECK THE GEM OPERATION
• Key in OFF position.

Yes

• Disconnect: GEM C201e.

GO to 

X7

.

• Key in ON position.

• Monitor the brake warning indicator with the GEM disconnected.

No

Does the brake warning indicator illuminate?

GO to 

X9

.

(Continued)

2003 Mustang, 8/2002 

Содержание ST1137-A












































Отзывы: