Ford POWER STROKE 2013 Скачать руководство пользователя | Manualshive

Страница: 58 / 95

background image

Checking coolant corrosion inhibitor additive strength

At specific mileage intervals of 15,000 miles (24,000 km), as listed in the

scheduled maintenance information

chapter, the coolant corrosion

inhibitor additive should be checked. The optional information display, if
equipped, will also display the message

CHECK COOLANT ADDITIVE

at this time. The purpose of checking is to verify the correct engine
coolant concentration (freeze point protection) and corrosion inhibitor
additive level (strength) of the coolant for maximum engine performance
and protection. Three products are available for ensuring the life and
health of the coolant: one tool, a test kit and a coolant inhibitor additive:

•

Rotunda tool 300–ROB75240 available from your dealer –
recommended refractometer to test coolant concentration.

•

Rotunda 328-R071–ELC (Antifreeze Coolant ELC Contamination Kit) –
Evaluates the corrosion inhibitor additive strength. Note the first step is
to verify the vehicle’s coolant concentration is in the correct range of 40
– 60%. Coolant concentrations outside this range will not provide valid
test results. If the report results in a pass (i.e., the cooling system does
not show excessive contamination/the corrosion inhibitor additive
strength is sufficient), no action is required. If the report results as
insufficient (does not pass), the corrosion inhibitor additive strength of
the coolant is too low. If the ENGINE COOLING SYSTEM corrosion
inhibitor additive strength is low, add 48 fluid oz. of Motorcraft®
Specialty Orange Engine Coolant Revitalizer. If the SECONDARY
COOLING SYSTEM corrosion inhibitor additive strength is low, add 16
fluid oz. of Motorcraft® Specialty Orange Engine Coolant Revitalizer.

•

Motorcraft® Specialty Orange Engine Coolant Revitalizer – Additive to
boost the corrosion inhibitor level based upon the test results of the
Antifreeze Coolant ELC Contamination Kit. The Revitalizer may be
added two times over the life of the coolant. If additional dosages are
required, the cooling system must be flushed and refilled per the
instructions in the Workshop Manual.

Refer to the

Capacities and Specifications

chapter for the proper

coolant and additive specifications.

Coolant change

At specific mileage intervals, as listed in the

scheduled maintenance

information,

the coolant should be changed. The optional information

display, if equipped, will also display the message

COOLANT CHANGE

REQUIRED

at this time.

Refer to the

Capacities and Specifications

chapter for the proper coolant.

Maintenance

57

2013 Diesel

(67l)

Supplement, 1st Printing
USA

(fus)

«
...
56
57
58
59
60
...
»

Содержание POWER STROKE 2013
































































































Отзывы:

Нет отзывов

Похожие инструкции для POWER STROKE 2013

VLT OneGearDrive

Бренд: Danfoss Страницы: 44

VLT OneGearDrive

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 20

Бренд: PCM Страницы: 83

Бренд: 3W Страницы: 20

Бренд: Zundapp Страницы: 52

Бренд: Vascat Страницы: 9

Бренд: Nissei Страницы: 16

Бренд: Saito Страницы: 27

Бренд: King Canada Страницы: 8

24 v High Performance Synchronous Motor

Бренд: Rega Страницы: 1

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 38

A50-10L Turnado

Бренд: Hacker Страницы: 4

Бренд: Hacker Страницы: 36

Бренд: Baotian Страницы: 41

Бренд: Jabiru Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды