manualshive.com logo in svg

Ford E-150 1997, Руководство пользователя

Поделиться
Скачать
Ford E-150 1997 Скачать руководство пользователя страница 45

Safety belt buckle pretensioner

Your vehicle is equipped with
safety belt buckle pretensioners at
the driver and front passenger
seating positions.

The safety belt buckle pretensioner
is a device which removes excess
webbing from the safety belt
system. The safety belt buckle
pretensioner uses the same crash
sensor system as the air bag
supplemental restraint system
(SRS). When the safety belt buckle
pretensioner deploys, the buckle
moves downward, pulling excess
webbing from the lap and shoulder
safety belt.

Combination lap and shoulder
belts

To fasten the safety belt, insert the
tongue into the slot in the buckle.

To disconnect the safety belt at:

•

front seating positions, push the
red release button on the end of

eco_comb_shoulder-belts

Seating and safety restraints

45

Содержание E-150 1997

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды