Ford E-150 1997 Скачать руководство пользователя страница 180

Страница: 180 / 192

Cutaway/commercial stripped
chassis models

E-250

E-350

E-Super Duty

1 = Overall
height

Refer to Body Builder for specifications.

2 = Track
front/rear

1762.8 mm
(69.4 in.)/1701.8
mm (67.0 in.)

1762.8 mm
(69.4 in.)/SRW
1701.8 mm
(67.0 in.), DRW
1859.3 mm
(73.2 in.)

1762.8 mm
(69.4 in.)/1973.6
mm (77.7 in.)

3 = Overall
width (excluding
mirrors)

Refer to Body Builder for specifications.

4 = Wheelbase

3149.6 mm
(124 in.)

3505 mm
(138 in.)
4013 mm
(158 in.)
4470 mm
(176 in.)

4013 mm
(158 in.)
4470 mm
(176 in.)

5 = Overall
length

Refer to Body Builder for specifications.

VEHICLE IDENTIFICATION
NUMBER

Complete Ford built vehicles

The vehicle identification number
is attached to your vehicle in the
following places:

•

On the metal tag attached to the
top of the instrument panel on
the driver’s side.

eco_dimensions_stripped

eco_vin
eco_vin_complete_vehicle

Capacities and specifications

180

Содержание E-150 1997

































































































































































































Результаты поиска

Содержание E-150 1997

Отзывы:

Бренды по названию

Популярные бренды

Ford E-150 1997, Руководство пользователя

Результаты поиска

Содержание E-150 1997

Отзывы:

Бренды по названию

Популярные бренды