Ford 2000 E-150 страница 19 Скачать руководство пользователя

Страница: 19 / 232

Fan speed control

Controls the volume of air circulated
in the vehicle.

Temperature control knob

Controls the temperature of the
airflow inside the vehicle. On
heater-only systems, the air cannot
be cooled below the outside
temperature.

Mode selector control

Controls the direction of the airflow
to the inside of the vehicle.

•

VENT-Distributes outside air through the instrument panel registers.

•

FLR-Allows for maximum heating. Distributes outside air through the
floor ducts.

•

OFF-Outside air is shut out and the fan will not operate.

•

MIX-Distributes outside air through the floor ducts and the windshield
defroster ducts.

•

-Distributes outside air through the windshield defroster ducts.

It can be used to clear ice or fog from the windshield.

Operating tips

•

In humid weather, select

before driving. This will reduce fogging

on your windshield. After a few minutes, select any desired position.

•

To prevent humidity buildup inside the vehicle, don’t drive with the
climate control system in the OFF position.

•

Don’t put objects under the front seat that will interfere with the
airflow to the back seats.

FAN

COOL

WARM

VENT

FLR

OFF

MIX

Controls and features

Содержание 2000 E-150









































































































































































































































Результаты поиска

Содержание 2000 E-150

Отзывы:

Похожие инструкции для 2000 E-150

Бренды по названию

Популярные бренды

Ford 2000 E-150, Руководство пользователя

Результаты поиска

Содержание 2000 E-150

Отзывы:

Похожие инструкции для 2000 E-150

Бренды по названию

Популярные бренды