FOR-A USF-106DC-12G Скачать руководство пользователя страница 27

Страница: 27 / 58

5-1-6-5. Knee (RGB) Clip

Selecting

Knee(RGB) Clip

in the Color Processor flow diagram opens the submenu as shown

below.

Item

Default

Setting (increments)

Description

White Clip

Disable

Disable
Enable

Enables/disables Knee Clip (White).

The following three parameters are available when White Clip is set to

Enable

Output Clip

100.0%

50.0 to 150.0%(0.5)

Sets the upper clip point in the RGB
color space.

Knee Slope

1.0

0.1 to 1.0 (0.05)

Sets the knee clip slope in high
luminance areas.

Knee Point

(Variable)

50.0% to
(Variable)(0.5)

Sets the knee clip start point in the high
luminance areas. Maximum and
default values vary depending on the
White Level (RGB white clip) setting.

Black Clip
Disable /
Enable

Disable

Disable
Enable

Enables/disables Knee Clip (Black).

The following parameter is available when Black Clip is set to

Enable

Output Clip

0.0%

-50.0 to 50.0% (0.1)

Sets the lower clip point in the RGB
color space.

5-1-6-6. Balance Color Correct

Selecting

Balance Color Correct

in the Color Processor flow diagram opens the submenu as

shown below.

Item

Default

Setting (increments)

Description

White Level
(RGB)

100.0%

0.0 - 200.0% (0.5)

Sets the white level by separately adjusting
R, G, and B components or simultaneously
adjusting them using Master.

Содержание USF-106DC-12G



























































Результаты поиска

Содержание USF-106DC-12G

Отзывы:

FOR-A USF-106DC-12G, Руководство по эксплуатации, Страница: 27 / 58

Результаты поиска

Содержание USF-106DC-12G

Отзывы: