background image

 

H300P Temperature Humidity Chamber

 

 

Page 2 

 

Introduction 

The H300P is a simple to use, versatile temperature / humidity chamber.  Its super compact design allows it 
to be placed on any table top.  Its solid state design means low noise and low power operation.  The solid 
state design also removes the need for user maintenance other that refilling water and desiccant. 

The H300P comes in four configurations: 

 

H300P

:  Simple set point control for temperature and humidity 

 

H300PRT

:  Profiling control for temperature, simple set point control for humidity 

 

H300PRH

:  Simple set point control for temperature, profiling control for humidity. 

 

H300PRTH

:  Profiling control for both temperature and humidity. 

A profiling controller allows the user to setup a program for the chamber to follow.  For instance:  Goto 
50%RH at 1%RH per minute, stay at 50%RH for 30 minutes, go to 75%RH as fast as possible, stay at 75%RH 
for 1 hour, etc. 

For easy remote access, configuration and monitoring get the Watlow EZ-LINK™ mobile app on your phone 
or tablet. The app uses Bluetooth® to communicate with the controllers. 

Safety Instructions 

Follow all 

CAUTION

 notices to prevent damage to the chamber. Failure to follow all 

CAUTION

 notices may 

void your warranty. 

WARNING

 indicates a potentially hazardous situation which, if not avoided, could result in death or serious 

injury. 

The safety alert symbol  

 precedes a general CAUTION or WARNING statement. 

The electrical hazard symbol  

 precedes an electric shock hazard CAUTION or WARNING statement. 

Installation Safety Notices 

 

WARNING

: The power cord is equipped with a NEMA 5-15P grounded GFCI plug.  To prevent a shock 

hazard, DO NOT defeat the ground or GFCI features. This device MUST be plugged into a 
properly grounded receptacle.

  

 

CAUTION

: The minimum clearance you should allow for proper ventilation around the chamber must be 

at least 6" from the rear, and 3’’ from both the left and right side. 

Содержание H300P

















Отзывы:

Похожие инструкции для H300P