background image

 

H300P Temperature Humidity Chamber

 

 

Page 10 

 

 

Changing Temperature Units 

To change the temperature controller units follow the procedure below: 

 

Press the Forward Arrow key once. The PM Plus controller will display a menu. 

 

Press the 

 key until 

Setup

 is highlighted. 

 

Press the Forward Arrow key once. The PM Plus controller will show the Setup Menu. 

 

Press the Forward Arrow key until 

Global

 is highlighted. 

 

Press the Forward Arrow key once. 

Display Units

 should be highlighted. 

 

Press the Forward Arrow key once. 

 

Press the 

+

 or 

 keys to select the desired units (F or C). 

 

Press the Home key when done. 

Changing the Set Point 

To change the target set point, use the numeric slider or the 

+

 or 

 keys until the desired set point is 

reached.  The controller has a 3 second delay before a new set point becomes active. 

Turning Temperature or Humidity Control OFF 

To turn control off to both temperature and humidity, use the 

CONT

 button on the chamber Controls.  You 

can also turn off control to either temperature or humidity individually using the appropriate PM PLUS 
controller, as follows: 

 

Press the Forward Arrow key once. 

Control Mode 1

 should be highlighted. 

 

Press the Forward Arrow key once. 

 

Press the 

+

 or 

 keys until 

Off

 is highlighted. 

Содержание H300P

















Отзывы:

Похожие инструкции для H300P