background image

01033729R05

© Follett LLC 5/18

Calgon is a licensed trademark distributed by Nu-Calgon, in the United States.
Dow Corning is a registered trademark of Dow Corning Corporation in the United States and other countries.
SafeCLEAN, SaniSponge, SensorSAFE, and Symphony Plus are trademarks of Follett LLC.

Follett is a registered trademarks of Follett LLC, registered in US.

801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com

Warranty Registration and Equipment Evaluation

Thank you for purchasing Follett ® equipment. Our goal is to deliver high value products and services that earn your complete 
satisfaction by delivering high-value products and services backed by outstanding customer and technical support. 
Please review the installation instructions thoroughly. It is important that the installation be performed to factory specifications 
so your equipment operates at its maximum efficiency.
Follett LLC will not be liable for any consequential damages, expenses, connecting or disconnecting charges, or any losses 
resulting from a defect of the machine. For full warranty details, visit our website www.follettice.com/productwarranties.
Registering your equipments helps Follett track your equipment's service history should you need to contact us for technical 
support, and your feedback helps us improve our products and services. Please visit www.follettice.com/support to complete 
the Warranty Registration form.
Should you have any questions, please contact Follett's technical support group at (877) 612-5086 or (610) 252-7301 and we 
will be happy to assist you.

Содержание 110CT425A

















Отзывы: