manualshive.com logo in svg

Folger Tech FT-5, Руководство пользователя

Поделиться
Скачать
Folger Tech FT-5 Скачать руководство пользователя страница 2

  

 

 FT-5 User Manual Page 1 

 

Table of Contents 

CONTENTS 

Introduction ............................................................................................................................................................................................... 3

 

Contact Folger Tech ................................................................................................................................................................................... 3

 

Inventory of Parts ...................................................................................................................................................................................... 4

 

Folger Tech FT-5 Parts ........................................................................................................................................................................... 4

 

Folger Tech FT-5 Hardware.................................................................................................................................................................... 5

 

Folger Tech FT-5 Laser Cut Parts ........................................................................................................................................................... 5

 

Printer Features & Definitions ................................................................................................................................................................. 12

 

Printer Assembly ...................................................................................................................................................................................... 16

 

1) Assemble the Frame ........................................................................................................................................................................ 17

 

2) Assemble the Base Plate ................................................................................................................................................................. 22

 

3) Assemble the Top Plate ................................................................................................................................................................... 24

 

4) Install Base and Top Plate................................................................................................................................................................ 25

 

5) Assemble Bed Plate ......................................................................................................................................................................... 26

 

6) Mounting Bed .................................................................................................................................................................................. 27

 

7) Assemble Y Gantry Rails .................................................................................................................................................................. 30

 

8) Gantry Assembly.............................................................................................................................................................................. 33

 

9) Hotend ............................................................................................................................................................................................. 37

 

10) Endstops and Belts ........................................................................................................................................................................ 43

 

11) Mounting Electronics and Spool Mount ........................................................................................................................................ 49

 

12) Assemble and Mount Heated Bed ................................................................................................................................................. 53

 

13) Wiring ............................................................................................................................................................................................ 56

 

Testing and Calibration ............................................................................................................................................................................ 67

 

ELECTRONICS Check List ...................................................................................................................................................................... 68

 

Software .............................................................................................................................................................................................. 70

 

Connect to the Printer & Loading Firmware ....................................................................................................................................... 70

 

Verify the Endstops ............................................................................................................................................................................. 71

 

Verify Motor Direction and Homing .................................................................................................................................................... 73

 

Adjusting Z Height ............................................................................................................................................................................... 74

 

Verify the Hot End Temperature ......................................................................................................................................................... 75

 

Содержание FT-5






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды