background image

2

Important Safety Instructions

Read these instructions.

1. 

Keep these instructions.

2. 

Heed all warnings.

3. 

Follow all instructions.

4. 

Do not use this apparatus near water.

5. 

Clean only with dry cloth.

6. 

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7. 

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8. 

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type 

9. 

plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your 
outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. 

Only use attachments/accessories specified by the manufacturer.

11. 

Unplug this apparatus during lightning storms or when unused for long periods of time.

12. 

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or 

13. 

plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate 
normally, or has been dropped.

  

    The apparatus shall be connected to a Mains socket outlet with a protective earthing connection. 

14. 

 
 

    Laite on liitettävä suojamaadoituskoskettimilla va rustettuumpistorasiaan 

 
 

    Apparatet mǻ tikoples jordet stikkontakt 

 
 

    Apparaten skall anslutas till jordat uttag

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

15. 

WARNING

16. 

 - To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture.

The appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

17. 

No naked flame sources, such as lighted candles, should be placed on the apparatus.

18. 

Do not use a damaged or frayed power cord.

19. 

If the mains plug supplying this apparatus incorporates a fuse then it should only be replaced with a fuse of identical or lower rupture value.

20. 

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when 

21. 

moving the cart/apparatus combination to avoid injury from tip-over.

GB

FIN

NOR

SWE

Содержание Liquid Saffire 56































Отзывы: