background image

• 

DO NOT  

use this appliance immediately below a fixed socket outlet.

• 

DO NOT  

use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture

could present a hazard.

WARNING : 

This heater is not equipped with a device to control the room temperature.  Do not use this heater in small

rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provid-
ed.
• 

CAUTION

:  This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device

that will switch on the appliance automatically, as a fire risk may occur if the heater is accidentally covered or displaced.
• Do not allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or simi-
lar material. A clearance space of at least one metre should be allowed in front of the appliance. 
• The electrical socket that the appliance uses MUST  be easily accessible. Do not route the supply cord directly in front of the heater unit.
• If the cord is damaged, it must be replaced by a service agent or competent person.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

The appliance is supplied with a pre-wired three pin plug,  (13Amp fuse rated), and 2 metres of electrical cable. It is therefore nec-
essary for a suitable electrical socket to be located within this distance and be easily accessible. 

This appliance is designed to be wall-hung, using the wall fixtures/fixings provided. DO NOT recess any part of
appliance into the wall. 

Read 

all  

the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging

and lay on the floor with its back surface downward. Note: DO NOT stand the appliance on its frame as this may cause distor-
tion. Check that the remaining packaging contents correlate with the component checklist below. Please dispose of all packaging
with care at your local recycling centre.

QUANTITY

DESCRIPTION

1

Wall Heater

1

Bag of Decorative Pebbles

1

Instruction Booklet

1

Wall Mounting Bracket

1

Screw and Wall-Plug Pack (3 x 40mm pozi pan head screws/3 x wall plugs)

The appliance is designed for wall mounting only, at a minimum distance of 100mm from the floor or hearth to the bottom edge
of decorative frame. The wall should be relatively flat and not interfere with any of the various vent holes in the back panel. The
wall must be structurally sound and constructed of a material capable of withstanding moderate heat. Finished plaster, conven-
tional wallpaper, dry-lined plasterboard are examples of suitable materials. Materials such as flock,  blown vinyl or embossed paper
which are sensitive to even small amounts of heat should be avoided as some discolouration may occur. 
If the appliance is to be mounted on a dry lined or a timber framed construction wall then the integrity and ability of the wall to
carry the weight of the appliance must be confirmed. It is important in these circumstances that any vapour control barrier and/or
structural member of the house frame are not damaged.  

Section

Contents

Page No.

1.0

Important Notes

2

2.0

Installation Requirements

2

3.0

Appliance Data

2

4.0

Unpacking the Appliance

2

5.0

Component Checklist

2

6.0

Site Requirements 

2

7.0 Appliance 

Disassembly

3

Section

Contents

Page No.

8.0

Fixing the Appliance

3

9.0

Placing the Pebbles

3

10.0

Operating the Fire

4

11.0

Safety Cut-Out System

4

12.0

Maintenance

13.0

Cleaning

4

14.0

Spares

4     

1.0 IMPORTANT NOTES

I N S TA L L AT I O N   &   U S E R   I N S T R U C T I O N S

©

2010 Focal Point Fires plc.

2

GB IE

©

2010 Focal Point Fires plc.

2.0 INSTALLATION REQUIREMENTS

3.0 APPLIANCE  DATA

Supply Voltage:

230/240V AC, 50Hz

Fuse Rating:

13 Amp

Heating Elements:

2 x 900W/2 x1000W

Lighting:

2 x 60W GE Fireglow “BC” bulbs

4.0 UNPACKING THE APPLIANCE

5.0 COMPONENT CHECKLIST

6.0 SITE REQUIREMENTS

Отзывы: