11.0
12.0
Placement of Pebbles:
Peel off any remaining protective plastic coatings on the front and rear frame, backpanel and any other surfaces.
Unpack the pebbles and arrange them over the fuel bed. The final pebble arrangement can only be done later when the appliance lamps
are switched on. For the best visual effect, do not push the pebbles up against the back panel, leave a gap of approximately 40mm between
the back panel and the pebbles. This allows light to shine up through the cut outs and illuminate the back panel.
OPERATING THE FIRE:
Read all instructions before use
Check that the fan outlet, mounted underneath the opening at the top, is not covered or obstructed in any way, and ensure the power to
the fire is switched on. The appliance is controlled using four switches mounted underneath the opening at the right hand side.
The left hand switch marked (0I), controls the main power to the appliance and switches on the visual light display. This feature can be used
independently of the heating features.
The next switch marked (*) operates the fan blower without heat, and can be used for cool air circulation. However for this feature, the main
power switch (0I), must also be in the “on” position.
The next switch with a “single bar” marked (I) operates the low heat, (1kW), setting.
The switch with “ two single bars” marked (II) operates the high heat, (2kW), setting.
To operate the fire in any of the above modes, the left hand switch marked (OI) must be switched to the “on” position. To operate the fire,
the left switch must be turned on first, followed by the second switch to start the blower, if required. To obtain heat from the appliance, the
I switch must then be operated for LOW heat, followed by the II switch for the HIGH heat setting.
The appliance can be switched off at any time, irrespective of the particular mode selected, by simply switching the left hand switch marked
(OI) to the “off” position. It is also recommended to unplug the power supply cable at the supply outlet when not in use.
SAFETY CUT-OUT SYSTEM:
This appliance has a safety cut-out system fitted which will activate if the air inlets or outlets are obstructed. For safety reasons the fire WILL
NOT switch on again automatically.
NOTE: The visual light effect will remain operational if the cut-out is activated, only the fan heater is prevented from operating.
The following procedure must be carried out before the fire can be operated again:
Unplug the power supply cable at the outlet socket and place all switches to off at the appliance. Leave the fire OFF for a period of not less
than 10 minutes, ensuring any obstructions are removed. Plug in the power supply cable at the outlet socket, and then switch on at the
appliance.
If the appliance fails to operate correctly, repeat the above procedure. If an attempt to switch on is made before the safety cut-out has reset,
the heaters may cut-out for a further period of time. If the sequence has been followed correctly and the heaters still fail to function, check
the power supply cable plug is plugged in to the outlet socket. If this is not the cause, call an electrician.
MAINTENANCE:
ALWAYS DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY OUTLET SOCKET BEFORE UNDERTAKING ANY MAINTENANCE.
Excluding lamps and fuses, use only genuine spare parts available from your supplier. Replacement lamps must be of the same wattage and
specification as those stated in Section 3.0 Appliance Data.
Replacing the light bulbs.
1. Switch off at the appliance, and then disconnect the appliance at the outlet socket.
2. Remove the decorative facia from the appliance (see section 6.0).
3. Remove the light bulb(s). Note that the bulbs have a conventional bayonet fitting. Replace with a new bulb(s).
4. Replace the decorative facia.
5. Reconnect electrical supply and check for correct operation of lamps and both spinner assemblies.
CLEANING:
ALWAYS DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY OUTLET SOCKET BEFORE UNDERTAKING ANY MAINTENANCE.
There are no specific requirements for care, other than regular cleaning of the general appliance. A wipe with a dry cloth is normally suffi-
cient. DO NOT use abrasive cleaners as they can damage the finish. Stainless steel parts (where applicable) may be cleaned using an appro-
priate metal cleaner or baby oil. Test on a hidden part of the stainless steel before cleaning. Clean only in the direction of the grain. Mirror
surfaces may be cleaned using normal glass cleaner.
SPARES:
Refer to Section 3.0 Appliance Data for lamp and fuse specification. Excluding lamps and fuses, use only genuine manufacturers spare parts
available from your supplier.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your
local authority or retailer for recycling advice.
As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to
amend details and/or specifications without prior notice.
10.0
3
9.0
13.0
F860579
