FMT Swiss AG 23295 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

background image

12

G

Operating instructions for turbine flow meter

The flow chart below shows the schematics of the display modes the LCD display may go through.
In this mode, the user may press RESET and thus change from the USER to the FACTORY FACTOR .
In order to confirm your choice, shortly press TOTAL while the display shows either USER or FACT.
After re-start, the meter will use the new calibration factor you just confirmed.

Tip
When you confirm restoration of the Factory K Factor, the old user factor will be deleted from

memory.

Standby

Standby

Standby

Reset long

Reset short

Total long

Total short

Time OL 1

Key

«
...
10
11
12
13
14
...
»

Содержание 23295

























Отзывы:

Нет отзывов

Похожие инструкции для 23295

Бренд: DAVIS Страницы: 12

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: Waterproof Страницы: 10

Бренд: Ocean Optics Страницы: 43

Бренд: Ocean Technology Systems Страницы: 12

Бренд: Ocean Reef Страницы: 24

Бренд: X-Rite Страницы: 50

Бренд: POSEIDON Страницы: 13

Бренд: Proteus Страницы: 4

Бренд: Hach Страницы: 2

Бренд: DeFelsko Страницы: 25

PowerMaster MTA15Z

Бренд: PowerMetrix Страницы: 13

Privia PX-860BK

Бренд: Casio Страницы: 67

Бренд: HOKUYO AUTOMATIC Страницы: 17

WATERPROOF PHTESTR 1 PH TESTER

Бренд: EUTECH INSTRUMENTS Страницы: 3

AirScout Gigacheck

Бренд: Greenlee Страницы: 19

Бренд: Keysight Technologies Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды